- 您現在的位置：買賣IC網 > PDF目錄385814 > SAA7712 (NXP Semiconductors N.V.) Sound effects DSP PDF資料下載
參數資料
| 型號： | SAA7712 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Sound effects DSP |
| 中文描述： | DSP的音效 |
| 文件頁數： | 24/44頁 |
| 文件大?。?/td> | 178K |
| 代理商： | SAA7712 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
1999 Aug 05
24
Philips Semiconductors
Preliminary specification
Sound effects DSP
SAA7712H
8.7
External control pins
For external control two input pins are implemented.
The status of these pins can be changed by applying a
logic level. The status of these pins is recorded in the
internal status register. The function of each input pin is
determined by the DSP software.
Pin DSP_IN1:
Logic 0 or left open-circuit means volume coefficients
updates are possible (default)
Logic 1 means no updates of volume coefficients are
possible.
Pin DSP_IN2:
If the 3-band spectrum analyser is used:
– Logic 1 will reset the band registers of the analyser
– Logic 0 or left open-circuit means no reset of the
band registers will be done (default).
If the 3-band spectrum analyser is not used:
–
The state of pin DSP_IN2 can be read via an I
2
C-bus
command.
To control external devices two output pins are
implemented. The status of these pins is controlled by the
DSP program. The functions of these pins are determined
by the DSP software.
Pin DSP_OUT1:
To drive pin DSP_OUT1 via an I
2
C-bus command.
Pin DSP_OUT2:
To drive pin DSP_OUT2 via an I
2
C-bus command.
8.8
Reset pin
The reset signal on pin DSP_RESET is active LOW and
has an internal pull-up resistor. Between this pin and
ground a capacitor should be connected to allow a proper
switch-on of the supply voltage. The capacitor value is
such that the chip is in the reset state as long as the power
supply is not stabilized.
A more or less fixed relationship between the
DSP_RESET time constant and the POM time constant is
obligatory.Thevoltageonpin POMdeterminesthecurrent
flowing in the DACs. For 0 V on pin POM, the DAC
currents are zero and so also the DACs output voltages.
Whena3 Vsupplyvoltage(V
DDA2
)issuppliedtopin POM,
the DAC currents are at their nominal (maximum) value.
Long before the DAC outputs get their nominal output
voltages, the DSP must be in normal operating mode to
reset the output register. Therefore, the time constant of
DSP_RESET must be shorter than the time constant of
POM. For advised capacitors see the application diagram.
The reset has the following function:
All I
2
C-bus registers are reset to their default values
The DSP algorithm is re-started
The external control output pins are reset
(see Section 8.7)
Pin SDA is high-impedance.
WhenthelevelontheresetpinisHIGH,theDSPalgorithm
starts to run.
In addition to the reset pin, there is also a software reset;
bit PC_reset (bit 15, 0FFDH, see Table 11). This reset has
the following function:
The DSP algorithm is re-started
The external control output pins are reset
(see Section 8.7).
相關PDF資料 |
PDF描述 |
|---|---|
| SAA8110G | Digital Signal Processor (DSP) for cameras(應用于照相中的數字信號處理器) |
| SAA8122A | Digital Still Camera Processor (ImagIC family)(數字靜態照相處理器) |
| SAA8122AEL | Digital Still Camera Processor ImagIC family |
| SAB-C504-2R24M | 8-Bit CMOS Microcontroller |
| SAB-C504-2R40M | 8-Bit CMOS Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA7712H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Sound effects DSP |
| SAA7715 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Signal Processor |
| SAA7715H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Signal Processor |
| SAA7724H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Car radio digital signal processor |
| SAA7740 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Audio Processing IC DAPIC |
發布緊急采購，3分鐘左右您將得到回復。