- 您現在的位置：買賣IC網 > PDF目錄385814 > SAA7388GP (NXP SEMICONDUCTORS) Error correction and host interface IC for CD-ROM ELM PDF資料下載
參數資料
| 型號： | SAA7388GP |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Error correction and host interface IC for CD-ROM ELM |
| 中文描述： | 8-BIT, 50.4 MHz, MICROCONTROLLER, PQFP80 |
| 文件頁數： | 9/60頁 |
| 文件大小： | 226K |
| 代理商： | SAA7388GP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
1996 Apr 26
9
Philips Semiconductors
Preliminary specification
Error correction and host interface IC for
CD-ROM (ELM)
SAA7388
6.1.21
DMACK
This signal is used in the ATAPI and Oak compatibility
modes during DMA transfers. The host pulls this signal
LOW in response to a DMARQ request to indicate that it is
ready to transfer data.
If this signal is not being used then it must be pulled HIGH
for SAA7388 to operate correctly.
6.1.22
IORDY/WAIT/HFBLB
In the ATAPI mode this signal is negated to extend the
host transfer cycle of any host register access. It is used in
PIO transfers. When IORDY is not negated it is in a
high-impedance state.
In the Sanyo compatibility mode the function of this signal
depends on the SELRQ input. If SELRQ is HIGH then
WAIT is set LOW to extend the host transfer cycle. If
SELRQ is LOW then WAIT acts as the DRQ signal in a
DMA transfer.
In the Oak compatibility mode this signal is the Host First
Byte Latch signal. A rising edge on this signal is used to
latch the first byte in a pseudo 16-bit DMA read. HFBLB
can only be HIGH when pseudo 16-bit DMA transfer mode
is selected.
6.1.23
SCRST/STEN
In the ATAPI or Oak compatibility mode this signal is pulled
LOW to reset the sub-CPU in response to a reset
command from the host.
In the Sanyo compatibility mode this signal is pulled LOW
to signal to the host that status bytes are available for
transfer.
6.1.24
DMARQ/DTEN
In the ATAPI or Oak compatibility mode this signal is
asserted when the SAA7388 is ready to transfer data
between the host and itself. In ATAPI single word and Oak
DMA transfers this occurs at every word. In ATAPI
multi-word DMA transfers this occurs at the start of the
transfer.
In the Sanyo compatibility mode this signal is pulled LOW
to signal to the host that data bytes are available for
transfer.
6.1.25
IRQ/EOP/HFBC
In the ATAPI mode this active HIGH signal indicates a host
interrupt request. It is asserted when the sub-CPU writes
to the ITRG register and is negated when the host reads
the status register or writes to the command register.
In the Sanyo compatibility mode this signal is set LOW
when the last data byte is transferred to or from the host.
In the Oak compatibility mode this is the Host First Byte
Cycle output and is HIGH while the first byte in the pseudo
16-bit DMA transfer is accessed. It should be used to
inhibit non-DMA transactions while the first byte is latched.
6.1.26
HD0
TO
HD15
These are the bidirectional Host Data signals. In the Sanyo
and Oak compatibility modes HD8 to HD15 are never
used.
6.1.27
DA0/CMD
In the ATAPI mode this is the host Data Address 0 signal.
In the Sanyo and Oak compatibility modes this input
selects between command or data transfers.
6.1.28
DA1
This is the ATAPI Data Address 1 signal.
6.1.29
DA2/ EJECT
In the ATAPI mode this is the Data Address 2 signal. In the
Oak compatibility mode this is the door switch input pin. Its
state is reflected in the TSTAT register.
6.1.30
CS2/SELRQ
In the ATAPI mode this is the Chip Select 2 signal. In the
Oak and Sanyo compatibility mode this is the data transfer
mode select input. It is used to select between PIO and
DMA transfers.
6.1.31
IOCS16
This open-collector signal is used in the ATAPI mode to
signal to the host that a 16-bit data port has been
addressed. It is not activated during DMA transfers.
相關PDF資料 |
PDF描述 |
|---|---|
| SAA7388 | Error correction and host interface IC for CD-ROM ELM |
| SAA7392HL | Channel encoder/decoder CDR60 |
| SAA7392 | Channel encoder/decoder CDR60(通道編碼器/譯碼器) |
| SAA7705H | Car radio Digital Signal Processor（DSP）(車載電臺數字信號處理器) |
| SAA7712H | Sound effects DSP(聲音效應數字信號處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA7390 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:High performance Compact Disc-Recordable CD-R controller |
| SAA7390GP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:High performance Compact Disc-Recordable CD-R controller |
| SAA7391 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ATAPI CD-R block encoder/decoder |
| SAA7391H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ATAPI CD-R block encoder/decoder |
| SAA7392 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Channel encoder/decoder CDR60 |
發布緊急采購，3分鐘左右您將得到回復。