參數資料
型號： S71JL064H80BAI020
廠商： ADVANCED MICRO DEVICES INC
元件分類： 存儲器
英文描述： SPECIALTY MEMORY CIRCUIT, PBGA73
封裝： 11.60 X 8 MM, FBGA-73
文件頁數： 51/95頁
文件大?。?/td> 2244K
代理商： S71JL064H80BAI020
February 25, 2004 S71JLxxxHxx_00A1
S29JL064H
55
Pre l i m i n a r y
tion of the SecSi Sector Region without raising any device pin to a high
voltage. Note that this method is only applicable to the SecSi Sector.
To verify the protect/unprotect status of the SecSi Sector, follow the algo-
rithm shown in Figure 3.
Once the SecSi Sector is locked and verified, the system must write the Exit SecSi
Sector Region command sequence to return to reading and writing the remainder
of the array.
The SecSi Sector lock must be used with caution since, once locked, there is no
procedure available for unlocking the SecSi Sector area and none of the bits in
the SecSi Sector memory space can be modified in any way.
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing
provides data protection against inadvertent writes (refer to Table 11 for com-
mand definitions). In addition, the following hardware data protection measures
prevent accidental erasure or programming, which might otherwise be caused by
spurious system level signals during VCC power-up and power-down transitions,
or from system noise.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This pro-
tects data during VCC power-up and power-down. The command register and all
internal program/erase circuits are disabled, and the device resets to the read
mode. Subsequent writes are ignored until VCC is greater than VLKO. The system
must provide the proper signals to the control pins to prevent unintentional writes
when VCC is greater than VLKO.
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write
cycle.
Figure 3. SecSi Sector Protect Verify
Write 60h to
any address
Write 40h to SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
START
RESET# =
VIH or VID
Wait 1 ms
Read from SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
If data = 00h,
SecSi Sector is
unprotected.
If data = 01h,
SecSi Sector is
protected.
Remove VIH or VID
from RESET#
Write reset
command
SecSi Sector
Protect Verify
complete
相關PDF資料
PDF描述
S71WS512NC0BAWEK2 Stacked Multi-Chip Product (MCP)
S71WS512NC0BAWEK3 Stacked Multi-Chip Product (MCP)
S71WS512NC0BAWEN0 Stacked Multi-Chip Product (MCP)
S71WS512NC0BAWEN2 Stacked Multi-Chip Product (MCP)
S71WS512NC0BAWEN3 Stacked Multi-Chip Product (MCP)
相關代理商/技術參數
參數描述
S71KL512SC0BHV000 功能描述:IC 512MB FLASH 64MB DRAM 24FBGA 制造商:cypress semiconductor corp 系列:HyperFlash? + HyperRAM? KL 包裝:托盤 零件狀態:在售 格式 - 存儲器:多芯（FLASH/RAM） 存儲器類型:FLASH + DRAM 存儲容量:512Mbit Flash, 64Mbit RAM 速度:100MHz 接口:并聯，串行 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:24-VBGA 供應商器件封裝:24-FBGA（6x8） 標準包裝:338
S71NS032J80 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP)
S71NS032J80BJWRA 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP)
S71NS032JA0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP)
S71NS032JA0BJWRT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*