- 您現在的位置：買賣IC網 > PDF目錄192300 > S29PL127J70BFI000 (SPANSION LLC) 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 PDF資料下載
參數資料
| 型號： | S29PL127J70BFI000 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| 封裝： | 11 X 8 MM, LEAD FREE, FBGA-80 |
| 文件頁數： | 60/97頁 |
| 文件大?。?/td> | 3042K |
| 代理商： | S29PL127J70BFI000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
September 7, 2007 S29PL-J_00_A10
S29PL-J
63
Da ta
Sh e e t
(Adv a n ce
In f o r m ation)
15.9
Program Suspend/Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming operation so that
data can read from any non-suspended sector. When the Program Suspend command is written during a
programming process, the device halts the programming operation within tPSL (program suspend latency)
and updates the status bits. Addresses are “don’t-cares” when writing the Program Suspend command. After
the programming operation has been suspended, the system can read array data from any non-suspended
sector. The Program Suspend command may also be issued during a programming operation while an erase
is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend.
If a read is needed from the Secured Silicon Sector area, then user must use the proper command
sequences to enter and exit this region. The system may also write the autoselect command sequence when
the device is in Program Suspend mode. The device allows reading autoselect codes in the suspended
sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode, the
device reverts to Program Suspend mode, and is ready for another valid operation. See “Autoselect
Command Sequence” for more information. After the Program Resume command is written, the device
reverts to programming. The system can determine the status of the program operation using the DQ7 or
DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more
information. The system must write the Program Resume command (address bits are “don’t care”) to exit the
Program Suspend mode and continue the programming operation. Further writes of the Program Resume
command are ignored. Another Program Suspend command can be written after the device has resumed
programming.
15.10 Command Definitions Tables
Table 15.1 on page 64 contains the Memory Array Command Definitions.
相關PDF資料 |
PDF描述 |
|---|---|
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
| S2C3R-1-12-H | 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS |
| S2C5R-1-12-RC | 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
| S2H3R-1H | 10 MHz - 1000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.2 dB INSERTION LOSS |
| S2L1R-RC | 1000 MHz - 2000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 0.9 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL127J70TAI130 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI130 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI131 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Rail/Tube |
| S29PL127J70TFI132 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
| S29PL127J70TFI133 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。