- 您現在的位置：買賣IC網 > PDF目錄192300 > S29PL127J70BFI000 (SPANSION LLC) 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 PDF資料下載
參數資料
| 型號： | S29PL127J70BFI000 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| 封裝： | 11 X 8 MM, LEAD FREE, FBGA-80 |
| 文件頁數： | 42/97頁 |
| 文件大?。?/td> | 3042K |
| 代理商： | S29PL127J70BFI000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
September 7, 2007 S29PL-J_00_A10
S29PL-J
47
Da ta
Sh e e t
(Adv a n ce
In f o r m ation)
12. Persistent Sector Protection
The Persistent Sector Protection method replaces the 12 V controlled protection method in previous flash
devices. This new method provides three different sector protection states:
Persistently Locked—The sector is protected and cannot be changed.
Dynamically Locked—The sector is protected and can be changed by a simple command.
Unlocked—The sector is unprotected and can be changed by a simple command.
To achieve these states, three types of “bits” are used:
Persistent Protection Bit
Persistent Protection Bit Lock
Persistent Sector Protection Mode Locking Bit
12.1
Persistent Protection Bit (PPB)
A single Persistent (non-volatile) Protection Bit is assigned to a maximum four sectors (see the sector
address tables for specific sector protection groupings). All 4 Kword boot-block sectors have individual sector
Persistent Protection Bits (PPBs) for greater flexibility. Each PPB is individually modifiable through the PPB
Write Command.
The device erases all PPBs in parallel. If any PPB requires erasure, the device must be instructed to
preprogram all of the sector PPBs prior to PPB erasure. Otherwise, a previously erased sector PPBs can
potentially be over-erased. The flash device does not have a built-in means of preventing sector PPBs over-
erasure.
12.2
Persistent Protection Bit Lock (PPB Lock)
The Persistent Protection Bit Lock (PPB Lock) is a global volatile bit. When set to “1”, the PPBs cannot be
changed. When cleared (“0”), the PPBs are changeable. There is only one PPB Lock bit per device. The PPB
Lock is cleared after power-up or hardware reset. There is no command sequence to unlock the PPB Lock.
12.3
Dynamic Protection Bit (DYB)
A volatile protection bit is assigned for each sector. After power-up or hardware reset, the contents of all
DYBs is “0”. Each DYB is individually modifiable through the DYB Write Command.
When the parts are first shipped, the PPBs are cleared, the DYBs are cleared, and PPB Lock is defaulted to
power up in the cleared state – meaning the PPBs are changeable.
When the device is first powered on the DYBs power up cleared (sectors not protected). The Protection State
for each sector is determined by the logical OR of the PPB and the DYB related to that sector. For the sectors
that have the PPBs cleared, the DYBs control whether or not the sector is protected or unprotected. By
issuing the DYB Write command sequences, the DYBs will be set or cleared, thus placing each sector in the
protected or unprotected state. These are the so-called Dynamic Locked or Unlocked states. They are called
dynamic states because it is very easy to switch back and forth between the protected and unprotected
conditions. This allows software to easily protect sectors against inadvertent changes yet does not prevent
the easy removal of protection when changes are needed. The DYBs maybe set or cleared as often as
needed.
The PPBs allow for a more static, and difficult to change, level of protection. The PPBs retain their state
across power cycles because they are non-volatile. Individual PPBs are set with a command but must all be
cleared as a group through a complex sequence of program and erasing commands. The PPBs are also
limited to 100 erase cycles.
The PPB Lock bit adds an additional level of protection. Once all PPBs are programmed to the desired
settings, the PPB Lock may be set to “1”. Setting the PPB Lock disables all program and erase commands to
the non-volatile PPBs. In effect, the PPB Lock Bit locks the PPBs into their current state. The only way to
clear the PPB Lock is to go through a power cycle. System boot code can determine if any changes to the
PPB are needed; for example, to allow new system code to be downloaded. If no changes are needed then
the boot code can set the PPB Lock to disable any further changes to the PPBs during system operation.
相關PDF資料 |
PDF描述 |
|---|---|
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
| S2C3R-1-12-H | 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS |
| S2C5R-1-12-RC | 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
| S2H3R-1H | 10 MHz - 1000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.2 dB INSERTION LOSS |
| S2L1R-RC | 1000 MHz - 2000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 0.9 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL127J70TAI130 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI130 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI131 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Rail/Tube |
| S29PL127J70TFI132 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
| S29PL127J70TFI133 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。