- 您現在的位置：買賣IC網 > PDF目錄192300 > S29PL127J70BFI000 (SPANSION LLC) 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 PDF資料下載
參數資料
| 型號： | S29PL127J70BFI000 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| 封裝： | 11 X 8 MM, LEAD FREE, FBGA-80 |
| 文件頁數： | 43/97頁 |
| 文件大?。?/td> | 3042K |
| 代理商： | S29PL127J70BFI000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
48
S29PL-J
S29PL-J_00_A10 September 7, 2007
Data
Sheet
(Adv an ce
Inf o r m a t io n)
The WP#/ACC write protect pin adds a final level of hardware protection to sectors SA1-133, SA1-134, SA2-
0 and SA2-1. When this pin is low it is not possible to change the contents of these sectors. These sectors
generally hold system boot code. The WP#/ACC pin can prevent any changes to the boot code that could
override the choices made while setting up sector protection during system initialization.
For customers who are concerned about malicious viruses there is another level of security - the persistently
locked state. To persistently protect a given sector or sector group, the PPBs associated with that sector need
to be set to “1”. Once all PPBs are programmed to the desired settings, the PPB Lock should be set to “1”.
Setting the PPB Lock automatically disables all program and erase commands to the Non-Volatile PPBs. In
effect, the PPB Lock “freezes” the PPBs into their current state. The only way to clear the PPB Lock is to go
through a power cycle.
It is possible to have sectors that have been persistently locked, and sectors that are left in the dynamic state.
The sectors in the dynamic state are all unprotected. If there is a need to protect some of them, a simple DYB
Write command sequence is all that is necessary. The DYB write command for the dynamic sectors switch
the DYBs to signify protected and unprotected, respectively. If there is a need to change the status of the
persistently locked sectors, a few more steps are required. First, the PPB Lock bit must be disabled by either
putting the device through a power-cycle, or hardware reset. The PPBs can then be changed to reflect the
desired settings. Setting the PPB lock bit once again will lock the PPBs, and the device operates normally
again.
The best protection is achieved by executing the PPB lock bit set command early in the boot code, and
protect the boot code by holding WP#/ACC = VIL.
Table 17 contains all possible combinations of the DYB, PPB, and PPB lock relating to the status of the
sector.
In summary, if the PPB is set, and the PPB lock is set, the sector is protected and the protection can not be
removed until the next power cycle clears the PPB lock. If the PPB is cleared, the sector can be dynamically
locked or unlocked. The DYB then controls whether or not the sector is protected or unprotected.
If the user attempts to program or erase a protected sector, the device ignores the command and returns to
read mode. A program command to a protected sector enables status polling for approximately 1 s before
the device returns to read mode without having modified the contents of the protected sector. An erase
command to a protected sector enables status polling for approximately 50 s after which the device returns
to read mode without having erased the protected sector.
The programming of the DYB, PPB, and PPB lock for a given sector can be verified by writing a DYB/PPB/
PPB lock verify command to the device. There is an alternative means of reading the protection status. Take
RESET# to VIL and hold WE# at VIH. (The high voltage A9 Autoselect Mode also works for reading the status
of the PPBs). Scanning the addresses (A18–A11) while (A6, A1, A0) = (0, 1, 0) will produce a logical ‘1” code
at device output DQ0 for a protected sector or a “0” for an unprotected sector. In this mode, the other
addresses are don’t cares. Address location with A1 = VIL are reserved for autoselect manufacturer and
device codes.
12.4
Persistent Sector Protection Mode Locking Bit
Like the password mode locking bit, a Persistent Sector Protection mode locking bit exists to guarantee that
the device remain in software sector protection. Once set, the Persistent Sector Protection locking bit
prevents programming of the password protection mode locking bit. This guarantees that a hacker could not
place the device in password protection mode.
相關PDF資料 |
PDF描述 |
|---|---|
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
| S2C3R-1-12-H | 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS |
| S2C5R-1-12-RC | 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
| S2H3R-1H | 10 MHz - 1000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.2 dB INSERTION LOSS |
| S2L1R-RC | 1000 MHz - 2000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 0.9 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29PL127J70TAI130 | 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI130 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Trays |
| S29PL127J70TFI131 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Rail/Tube |
| S29PL127J70TFI132 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
| S29PL127J70TFI133 | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 70NS 56TSOP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。