參數資料
型號： S1C60N05D0A0100
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, UUC53
封裝： DIE-53
文件頁數： 36/95頁
文件大?。?/td> 736K
代理商： S1C60N05D0A0100
44
ATtiny4/5/9/10 [DATASHEET]
8127F–AVR–02/2013
Figure 10-5. Synchronization when Reading a Software Assigned Pin Value
10.2.5
Digital Input Enable and Sleep Modes
As shown in Figure 10-2 on page 41, the digital input signal can be clamped to ground at the input of the schmitt-
trigger. The signal denoted SLEEP in the figure, is set by the MCU Sleep Controller in Power-down and Standby
modes to avoid high power consumption if some input signals are left floating, or have an analog signal level close
to V
CC/2.
SLEEP is overridden for port pins enabled as external interrupt pins. If the external interrupt request is not enabled,
SLEEP is active also for these pins. SLEEP is also overridden by various other alternate functions as described in
If a logic high level (“one”) is present on an asynchronous external interrupt pin configured as “Interrupt on Rising
Edge, Falling Edge, or Any Logic Change on Pin” while the external interrupt is not enabled, the corresponding
External Interrupt Flag will be set when resuming from the above mentioned Sleep mode, as the clamping in these
sleep mode produces the requested logic change.
10.2.6
Unconnected Pins
If some pins are unused, it is recommended to ensure that these pins have a defined level. Even though most of
the digital inputs are disabled in the deep sleep modes as described above, floating inputs should be avoided to
reduce current consumption in all other modes where the digital inputs are enabled (Reset, Active mode and Idle
mode).
The simplest method to ensure a defined level of an unused pin, is to enable the internal pull-up. In this case, the
pull-up will be disabled during reset. If low power consumption during reset is important, it is recommended to use
an external pull-up or pulldown. Connecting unused pins directly to V
CC or GND is not recommended, since this
may cause excessive currents if the pin is accidentally configured as an output.
out PORTx, r16
nop
in r17, PINx
0xFF
0x00
0xFF
SYSTEM CLK
r16
INSTRUCTIONS
SYNC LATCH
PINxn
r17
t pd
相關PDF資料
PDF描述
S1C621A0F0A0100 MICROCONTROLLER, PQFP80
S1C63158D0A010P 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, UUC53
S1C7XXXF00E199 16-BIT, 90 MHz, RISC MICROCONTROLLER, PQFP
S2041 PHOTO TRANSISTOR DETECTOR
S3P44R10 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
相關代理商/技術參數
參數描述
S1C60N08 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C60N16 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C60R08 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63004 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
S1C63008 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*