- 您現在的位置：買賣IC網 > PDF目錄98067 > S-4561A 16 X 60 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC166 PDF資料下載
參數資料
| 型號： | S-4561A |
| 元件分類： | 顯示控制器 |
| 英文描述： | 16 X 60 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC166 |
| 封裝： | 7.65 X 2 MM, DIE-166 |
| 文件頁數： | 48/48頁 |
| 文件大?。?/td> | 427K |
| 代理商： | S-4561A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁
LCD Controller-Driver
S-4561A
Seiko Instruments Inc.
9
1.2 Serial Interface
Serial interface is engaged when the P/SX terminal is “L.” The instruction code is read at the rising edge of the serial clock
(SCLK). Serial data is input in numerical order from DB0 to DB7. The instruction code is the same as that for the parallel
data. Connect and fix the P/SX terminal to VSS. Connect pins DB2 through DB7, R/WX, and C86 to “OPEN.”
P/SX:
“L” Serial Interface Operation/Fix to VSS.
RS:
Write in the “L”Instruction Register.
Write in the “H” Data Register.
E:
“L” Active
DB0:
Serial Data Input Pin (SDI)
DB1:
Serial Clock Input Pin (SCLK)
DB2 to DB7:
OPEN
R/WX:
OPEN
C86:
OPEN
Figure 7 Serial Interface
Table 10 Serial Interface
Taking into consideration external or reflective noises, optimize the serial clock wiring.
Always check operations after
mounting the IC on your device.
2.
Busy
When the BUSY flag points “1,” it shows that an instruction is being executed. The BUSY flag is read to DB7 by the
ADDRESS READ command. In case of commands other than the RESET or the DISPLAY CLEAR, there is no need for
confirming the BUSY flag. This is because that the instruction is completed within the cycle time specified in accordance with
the timing characteristics. After confirming that BUSY flag points “0” during RESET or DISPLAY CLEAR operation or after
the specified wait time, write the next command. When the BUSY flag points “1,” any command other than the ADDRESS
READ cannot be accepted.
When a serial interface is selected, the BUSY READ is not available.
3.
Address Counter
The Address Counter (AC) gives respective addresses for DDRAM, CGRAM, ICONRAM or ICON BLINK RAM according to
the contents of the AC. Only one RAM among the four kinds of RAMs is selected by the RAM ADDRESS SETTING
command. After the ADDRESS SETTING command is executed, the display data can be read and written in the selected
RAM. The contents of the RAM AC, where the ADDRESS READ command, is also selected are read. Increment and
decrement of the AC are automatically executed after the READ or WRITE command is executed. Once an address is set,
READ and WRITE commands can be input in succession.
E
RS
Operation
L
Write/Input to Instruction Register
L
H
Write to Data Register
HL
HH
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
E
RS
SCLK
(DB1)
SDI
(DB0)
DB0
Valid
相關PDF資料 |
PDF描述 |
|---|---|
| S-75L86ANC-5L8-TFG | LV/LV-A/LVX/H SERIES, 2-INPUT XOR GATE, PDSO5 |
| S-75V86ANC-5V8-TFG | AHC/VHC SERIES, 2-INPUT XOR GATE, PDSO5 |
| S-75V08ANC-5V2-TFG | AHC/VHC SERIES, 2-INPUT AND GATE, PDSO5 |
| S-75V00ANC-5V1-TFG | AHC/VHC SERIES, 2-INPUT NAND GATE, PDSO5 |
| S-75V00ANC-5V1-TF | AHC/VHC SERIES, 2-INPUT NAND GATE, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-4562A | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:LCD CONTROLLER DRIVER |
| S4565-8 | 制造商:DANAHER - INDUSTRIAL/SPECIALTY 功能描述:ENDBELL ADAPTER |
| S-4568 | 制造商:WAVETEK 功能描述:S-4568 |
| S4-56R-E | 功能描述:端子 Tubular Ring term non-insulated 4 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
| S4-56R-T | 功能描述:端子 #4 5/16" RING TERM RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
發布緊急采購，3分鐘左右您將得到回復。