參數資料
型號： PSD813F2-15JT
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52
封裝： PLASTIC, LCC-52
文件頁數： 59/103頁
文件大?。?/td> 1180K
代理商： PSD813F2-15JT
59/103
PSD8XXF2/3/4/5
Automatic Power-down (APD) Unit and Power-
down Mode. The APD Unit, shown in Figure 29,
puts the PSD8XXFX into Power-down mode by
monitoring the activity of Address Strobe (ALE/AS,
PD0). If the APD Unit is enabled, as soon as activ-
ity on Address Strobe (ALE/AS, PD0) stops, a four
bit counter starts counting. If Address Strobe
(ALE/AS, PD0) remains inactive for fifteen clock
periods of CLKIN (PD1), Power-down (PDN) goes
High, and the PSD8XXFX enters Power-down
mode, as discussed next.
Power-down Mode. By default, if you enable the
APD Unit, Power-down mode is automatically en-
abled. The device enters Power-down mode if Ad-
dress Strobe (ALE/AS, PD0) remains inactive for
fifteen periods of CLKIN (PD1).
The following should be kept in mind when the
PSD8XXFX is in Power-down mode:
s
If Address Strobe (ALE/AS, PD0) starts pulsing
again, the PSD8XXFX returns to normal
Operating mode. The PSD8XXFX also returns
to normal Operating mode if either PSD Chip
Select Input (CSI, PD2) is Low or the Reset
(RESET) input is High.
s
The MCU address/data bus is blocked from all
memory and PLDs.
s
Various signals can be blocked (prior to Power-
down mode) from entering the PLDs by setting
the appropriate bits in the PMMR registers. The
blocked signals include MCU control signals
and the common CLKIN (PD1). Note that
blocking CLKIN (PD1) from the PLDs does not
block CLKIN (PD1) from the APD Unit.
s
All PSD8XXFX memories enter Standby mode
and are drawing standby current. However, the
PLD and I/O ports blocks do
not go into Standby
Mode because you don’t want to have to wait for
the logic and I/O to “wake-up” before their
outputs can change. See Table 28 for Power-
down mode effects on PSD8XXFX ports.
s
Typical standby current is of the order of
microamperes. These standby current values
assume that there are no transitions on any PLD
input.
Table 28. Power-down Mode’s Effect on Ports
Figure 29. APD Unit
Table 29. PSD8XXFX Timing and Stand-by Current during Power-down Mode
Note: 1. Power-down does not affect the operation of the PLD. The PLD operation in this mode is based only on the Turbo bit.
2. Typical current consumption assuming no PLD inputs are changing state and the PLD Turbo bit is 0.
Port Function
Pin Level
MCU I/O
No Change
PLD Out
No Change
Address Out
Undefined
Data Port
Tri-State
Peripheral I/O
Tri-State
Mode
PLD Propagation
Delay
Memory
Access Time
Access Recovery Time
to Normal Access
Typical Stand-by Current
5V VCC
3V VCC
Power-down
Normal tPD (Note
1)
No Access
tLVDV
75 A (Note 2)
25 A (Note 2)
APD EN
PMMR0 BIT 1=1
ALE
RESET
CSI
CLKIN
TRANSITION
DETECTION
EDGE
DETECT
APD
COUNTER
POWER DOWN
(PDN)
DISABLE BUS
INTERFACE
EEPROM SELECT
FLASH SELECT
SRAM SELECT
PD
CLR
PD
DISABLE
FLASH/EEPROM/SRAM
PLD
SELECT
AI02891
相關PDF資料
PDF描述
PSD813F5V-20MT 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52
PSD853F2-15JIT 128K X 8 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQCC52
PSD833F2-15M 1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP52
PSD835G2V-B-90MI Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD835G2V-B-90U Configurable Memory System on a Chip for 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
PSD813F2-15M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2-15MI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2-15MIT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2-15MT 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs
PSD813F2-15U 制造商:WSI 功能描述: 制造商:WSI 功能描述:1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP64
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*