參數資料
型號： NAND08GR3B2AN1F
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 1G X 8 FLASH 1.8V PROM, 35 ns, PDSO48
封裝： 12 X 20 MM, ROHS COMPLIANT, PLASTIC, TSOP-48
文件頁數： 20/57頁
文件大?。?/td> 887K
代理商： NAND08GR3B2AN1F
27/57
NAND01G-B, NAND02G-B, NAND04G-B, NAND08G-B
Block Erase
Erase operations are done one block at a time. An
erase operation sets all of the bits in the ad-
dressed block to ‘1’. All previous data in the block
is lost.
An erase operation consists of three steps (refer to
1.
One bus cycle is required to setup the Block
Erase command. Only addresses A18-A27
(x8) or A17-A26 (x16) are used, the other
address inputs are ignored.
2.
two or three bus cycles are then required to
load the address of the block to be erased.
Refer to Table 8. and Table 9. for the block
addresses of each device.
3.
one bus cycle is required to issue the Block
Erase confirm command to start the P/E/R
Controller.
The operation is initiated on the rising edge of
write Enable, W, after the confirm command is is-
sued. The P/E/R Controller handles Block Erase
and implements the verify process.
During the Block Erase operation, only the Read
Status Register and Reset commands will be ac-
cepted, all other commands will be ignored.
Once the program operation has completed the P/
E/R Controller bit SR6 is set to ‘1’ and the Ready/
Busy signal goes High. If the operation completed
successfully, the Write Status Bit SR0 is ‘0’, other-
wise it is set to ‘1’.
Figure 16. Block Erase Operation
Reset
The Reset command is used to reset the Com-
mand Interface and Status Register. If the Reset
command is issued during any operation, the op-
eration will be aborted. If it was a program or erase
operation that was aborted, the contents of the
memory locations being modified will no longer be
valid as the data will be partially programmed or
erased.
If the device has already been reset then the new
Reset command will not be accepted.
The Ready/Busy signal goes Low for tBLBH4 after
the Reset command is issued. The value of tBLBH4
depends on the operation that the device was per-
forming when the command was issued, refer to
Table 25. for the values.
I/O
RB
Block Address
Inputs
SR0
ai07593
D0h
70h
60h
Block Erase
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH3
(Erase Busy time)
相關PDF資料
PDF描述
NAND04GW4B2AN1E 256M X 16 FLASH 3V PROM, 35 ns, PDSO48
NAND02GW4B2AN1T 128M X 16 FLASH 3V PROM, 35 ns, PDSO48
NAND04GR4B2CN1F 256M X 16 FLASH 1.8V PROM, 35 ns, PDSO48
NAND08GW3B2CZL1F 1G X 8 FLASH 3V PROM, 25000 ns, PBGA52
NAND128W3A2BV6E 16M X 8 FLASH 3V PROM, 12000 ns, PDSO48
相關代理商/技術參數
參數描述
NAND08GR3B4CZL6E 制造商:Micron Technology Inc 功能描述:NAND - Trays
NAND08GR3B4CZL6F 制造商:Micron Technology Inc 功能描述:NAND - Tape and Reel
NAND08GW3B2AN6E 功能描述:閃存 4 GBit 2112 Byte 1056 WP 1.8v/3v RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND08GW3B2AN6F 功能描述:閃存 4 GB 2112B 1056 Word Pg 1.8V/3V RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
NAND08GW3B2BN6E 制造商:Micron Technology Inc 功能描述:NAND & S.MEDIA FLASH - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*