參數資料
型號： MT9074AL
廠商： Mitel Networks Corporation
英文描述： T1/E1/J1 Single Chip Transceiver
中文描述： T1/E1/J1收發單芯片收發器
文件頁數： 24/122頁
文件大?。?/td> 372K
代理商： MT9074AL
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
MT9074
Advance Information
24
N bytes of data. The HDLC does not distinguish
between the control and information fields and a
packet does not need to contain an information field
to be valid.
The FCS field, which precedes the closing flag,
consists of two bytes. A cyclic redundancy check
utilizing
the
CRC-CCITT
polynomial “X
16
+X
12
+X
5
+1” produces the 16-bit
FCS. In the transmitter the FCS is calculated on all
bits of the address and data field. The complement
of the FCS is transmitted, most significant bit first, in
the FCS field. The receiver calculates the FCS on
the incoming packet address, data and FCS field and
compares the result to “F0B8”. If no transmission
errors are detected and the packet between the flags
is at least 32 bits in length then the address and data
are entered into the receive FIFO minus the FCS
which is discarded.
standard
generator
Data Transparency (Zero Insertion/Deletion)
Transparency ensures that the contents of a data
packet do not imitate a flag, go-ahead, frame abort
or idle channel. The contents of a transmitted frame,
between the flags, is examined on a bit-by-bit basis
and a 0 bit is inserted after all sequences of 5
contiguous 1 bits (including the last five bits of the
FCS). Upon receiving five contiguous 1s within a
frame the receiver deletes the following 0 bit.
Invalid Frames
A frame is invalid if one of the following four
conditions exists (Inserted zeros are not part of a
valid count):
If the FCS pattern generated from the
received data does not match the “F0B8”
pattern then the last data byte of the packet
is written to the received FIFO with a ‘bad
packet’ indication.
A short frame exists if there are less than 25
bits between the flags. Short frames are
ignored by the receiver and nothing is written
to the receive FIFO.
Packets which are at least 25 bits in length
but less than 32 bits between the flags are
also invalid. In this case the data is written to
the FIFO but the last byte is tagged with a
“bad packet” indication.
If a frame abort sequence is detected the
packet is invalid. Some or all of the current
packet will reside in the receive FIFO,
assuming the packet length before the abort
sequence was at least 26 bits long.
Frame Abort
The transmitter will abort a current packet by
substituting a zero followed by seven contiguous 1s
in place of the normal packet. The receiver will abort
upon reception of seven contiguous 1s occurring
between the flags of a packet which contains at least
26 bits.
Note that should the last received byte before the
frame abort end with contiguous 1s, these are
included in the seven 1s required for a receiver
abort. This means that the location of the abort
sequence in the receiver may occur before the
location of the abort sequence in the originally
transmitted packet. If this happens then the last data
written to the receive FIFO will not correspond
exactly with the last byte sent before the frame abort.
Interframe Time Fill and Link Channel States
When the HDLC transmitter is not sending packets it
will wait in one of two states
Interframe Time Fill state: This is a
continuous series of flags occurring between
frames indicating that the channel is active
but that no data is being sent.
Idle state: An idle Channel occurs when at
least 15 contiguous 1s are transmitted or
received.
In both states the transmitter will exit the wait state
when data is loaded into the transmitter FIFO.
Go-Ahead
A go ahead is defined as the pattern "011111110"
(contiguous 7Fs) and is the occurrence of a frame
abort sequence followed by a zero, outside of the
boundaries of a normal packet. Being able to
distinguish a proper (in packet) frame abort
sequence from one occurring outside of a packet
allows a higher level of signalling protocol which is
not part of the HDLC specifications.
HDLC Functional Description
The HDLC transceiver can be reset by either the
power reset input signal or by the HRST Control bit
in the test control register (software reset). When
reset, the HDLC Control Registers are cleared,
resulting in the transmitter and receiver being
disabled. The Receiver and Transmitter can be
enabled independent of one another through Control
Register 1. The transceiver input and output are
enabled when the enable control bits in Control
Register 1 are set. Transmit to receive loopback as
相關PDF資料
PDF描述
MT9074AP T1/E1/J1 Single Chip Transceiver
MT9074 T1/E1/J1 Single Chip Transceiver(T1/E1/J1單片收發器)
MT9075B E1 Single Chip Transceiver
MT9075B E1 Single Chip Transceiver(E1單片收發器)
MT9075 E1 Single Chip Transceiver
相關代理商/技術參數
參數描述
MT9074AL1 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 5V 100MQFP - Trays
MT9074AP 制造商:Microsemi Corporation 功能描述:
MT9074AP1 制造商:Microsemi Corporation 功能描述:T1/E1/J1 SGLE CHIP XSCR 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 5V 68PLCC - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX SGL T1/E1 68PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX SGL T1/E1 68PLCC
MT9074APR 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 Single Chip Transceiver
MT9074APR1 制造商:Microsemi Corporation 功能描述:FRAMER E1/J1/T1 5V 68PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 5V 68PLCC - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*