![](http://datasheet.mmic.net.cn/390000/MT58L512Y32D_datasheet_16823637/MT58L512Y32D_8.png)
8
16Mb: 1 Meg x 18, 512K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L1MY18D_2.p65 – Rev 7/00
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2000, Micron Technology, Inc.
16Mb: 1 MEG x 18, 512K x 32/36
PIPELINED, DCD SYNCBURST SRAM
ADVANCE
FBGA PIN DESCRIPTIONS
x18
6R
6P
x32/x36
6R
6P
2A, 2B, 3P,
SY MBOL
SA0
SA1
SA
TY PE
Input
DESCRIPTION
Synchronous Address Inputs: These inputs are registered and must
meet the setup and hold times around the rising edge of CLK.
2A, 2B, 3P,
3R, 4P, 4R, 6N, 3R, 4P, 4R, 6N,
8P, 8R, 9P, 9R,
10A, 10B, 10P, 9R, 10A, 10B,
10R, 11A, 11P, 10P, 10R, 11P,
11R
5B
4A
–
–
8P, 8R, 9P,
11R
5B
5A
4A
4B
BWa#
BWb#
BWc#
BWd#
Input
Synchronous Byte Write Enables: These active LOW inputs allow
individual bytes to be written and must meet the setup and hold
times around the rising edge of CLK. A byte write enable is LOW
for a WRITE cycle and HIGH for a READ cycle. For the x18 version,
BWa# controls DQa’s and DQPa; BWb# controls DQb’s and DQPb.
For the x32 and x36 versions, BWa# controls DQa’s and DQPa; BWb#
controls DQb’s and DQPb; BWc# controls DQc’s and DQPc; BWd#
controls DQd’s and DQPd. Parity is only available on the x18 and
x36 versions.
Byte Write Enable: This active LOW input permits BYTE WRITE
operations and must meet the setup and hold times around the
rising edge of CLK.
Global Write: This active LOW input allows a full 18-, 32- or 36-bit
WRITE to occur independent of the BWE# and BWx# lines and must
meet the setup and hold times around the rising edge of CLK.
Clock: This signal registers the address, data, chip enable, byte write
enables, and burst control inputs on its rising edge. All synchronous
inputs must meet setup and hold times around the clock’s rising
edge.
Synchronous Chip Enable: This active LOW input is used to enable
the device and conditions the internal use of ADSP#. CE# is sampled
only when a new external address is loaded.
Synchronous Chip Enable: This active LOW input is used to enable
the device and is sampled only when a new external address is
loaded.
Snooze Enable: This active HIGH, asynchronous input causes the
device to enter a low-power standby mode in which all data in the
memory array is retained. When ZZ is active, all other inputs are
ignored.
Synchronous Chip Enable: This active HIGH input is used to enable
the device and is sampled only when a new external address is
loaded.
Output Enable: This
active LOW, asynchronous input enables the
data I/O output drivers.
7A
7A
BWE#
Input
7B
7B
GW#
Input
6B
6B
CLK
Input
3A
3A
CE#
Input
6A
6A
CE2#
Input
11H
11H
ZZ
Input
3B
3B
CE2
Input
8B
8B
OE#(G#)
Input
(continued on next page)