- 您現在的位置：買賣IC網 > PDF目錄385640 > MT58L512Y32D (Micron Technology, Inc.) 16Mb SYNCBURST⑩ SRAM PDF資料下載
參數資料
| 型號： | MT58L512Y32D |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | 16Mb SYNCBURST⑩ SRAM |
| 中文描述： | ⑩的SRAM 16Mb的SYNCBURST |
| 文件頁數： | 25/34頁 |
| 文件大?。?/td> | 526K |
| 代理商： | MT58L512Y32D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
25
16Mb: 1 Meg x 18, 512K x 32/36 Pipelined, DCD SyncBurst SRAM
MT58L1MY18D_2.p65 – Rev 7/00
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2000, Micron Technology, Inc.
16Mb: 1 MEG x 18, 512K x 32/36
PIPELINED, DCD SYNCBURST SRAM
ADVANCE
register is connected to TDI, and the LSB is connected to
TDO.
IDENTIFICATION (ID) REGISTER
The ID register is loaded with a vendor-specific, 32-
bit code during the Capture-DR state when the IDCODE
command is loaded in the instruction register. The
IDCODE is hardwired into the SRAM and can be shifted
out when the TAP controller is in the Shift-DR state. The
ID register has a vendor code and other information
described in the Identification Register Definitions table.
TAP INSTRUCTION SET
OVERVIEW
Eight different instructions are possible with the
three-bit instruction register. All combinations are listed
in the Instruction Codes table. Three of these instruc-
tions are listed as RESERVED and should not be used.
The other five instructions are described in detail below.
The TAP controller used in this SRAM is not fully
compliant to the 1149.1 convention because some of
the mandatory 1149.1 instructions are not fully imple-
mented. The TAP controller cannot be used to load
address, data or control signals into the SRAM and
cannot preload the I/O buffers. The SRAM does not
implement the 1149.1 commands EX TEST or INTEST or
the PRELOAD portion of SAMPLE/PRELOAD; rather it
performs a capture of the I/O ring when these instruc-
tions are executed.
Instructions are loaded into the TAP controller dur-
ing the Shift-IR state when the instruction register is
placed between TDI and TDO. During this state, instruc-
tions are shifted through the instruction register through
the TDI and TDO pins. To execute the instruction once
it is shifted in, the TAP controller needs to be moved into
the Update-IR state.
EXTEST
EX TEST is a mandatory 1149.1 instruction which is
to be executed whenever the instruction register is loaded
with all 0s. EX TEST is not implemented in this SRAM
TAP controller, and therefore this device is not compli-
ant to 1149.1.
The TAP controller does recognize an all-0 instruc-
tion. When an EX TEST instruction is loaded into the
instruction register, the SRAM responds as if a SAMPLE/
PRELOAD instruction has been loaded. There is one
difference between the two instructions. Unlike the
SAMPLE/PRELOAD instruction, EX TEST places the SRAM
outputs in a High-Z state.
IDCODE
The IDCODE instruction causes a vendor-specific,
32-bit code to be loaded into the instruction register. It
also places the instruction register between the TDI and
TDO pins and allows the IDCODE to be shifted out of the
device when the TAP controller enters the Shift-DR
state. The IDCODE instruction is loaded into the in-
struction register upon power-up or whenever the TAP
controller is given a test logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan
register to be connected between the TDI and TDO pins
when the TAP controller is in a Shift-DR state. It also
places all SRAM outputs into a High-Z state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruc-
tion. The PRELOAD portion of this instruction is not
implemented, so the device TAP controller is not fully
1149.1-compliant.
When the SAMPLE/PRELOAD instruction is loaded
into the instruction register and the TAP controller is in
the Capture-DR state, a snapshot of data on the inputs
and bi-directional pins is captured in the boundary scan
register.
The user must be aware that the TAP controller clock
can only operate at a frequency up to 10 MHz, while the
SRAM clock operates more than an order of magnitude
faster. Because there is a large difference in the clock
frequencies, it is possible that during the Capture-DR
state, an input or output will undergo a transition. The
TAP may then try to capture a signal while in transition
(metastable state). This will not harm the device, but
there is no guarantee as to the value that will be cap-
tured. Repeatable results may not be possible.
To guarantee that the boundary scan register will
capture the correct value of a signal, the SRAM signal
must be stabilized long enough to meet the TAP
controller’s capture setup plus hold time (
t
CS plus
t
CH).
The SRAM clock input might not be captured correctly
if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an
issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK# captured in
the boundary scan register.
Once the data is captured, it is possible to shift out the
data by putting the TAP into the Shift-DR state. This
places the boundary scan register between the TDI and
TDO pins.
Note that since the PRELOAD part of the command
is not implemented, putting the TAP to the Update-DR
state while performing a SAMPLE/PRELOAD instruction
will have the same effect as the Pause-DR command.
相關PDF資料 |
PDF描述 |
|---|---|
| MT58L64L18F | 64K x 18, 3.3V I/O, Flow-Through SyncBurst SRAM(1Mb,3.3V輸入/輸出,流通式同步脈沖靜態RAM) |
| MT58L32L32F | 32K x 32， 3.3V I/O, Flow-Through SyncBurst SRAM(1Mb,3.3V輸入/輸出,流通式同步脈沖靜態RAM) |
| MT58L32L36F | 32K x 36， 3.3V I/O, Flow-Through SyncBurst SRAM(1Mb,3.3V輸入/輸出，流通式同步脈沖靜態RAM) |
| MT58L64L18P | 64K x 18, 3.3V I/O, Pipelined, SCD SyncBurst SRAM(1Mb,3.3V輸入/輸出，流水線式，單循環取消選擇，同步脈沖靜態存儲器) |
| MT58L32L32P | 32K x 32, 3.3V I/O, Pipelined, SCD SyncBurst SRAM(1Mb,3.3V輸入/輸出，流水線式，單循環取消選擇，同步脈沖靜態存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT58L512Y32DT-10 | 制造商:Cypress Semiconductor 功能描述:512KX32 SRAM PLASTIC TQFP 3.3V 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MT58L512Y32DT-10 ES | 制造商:Cypress Semiconductor 功能描述:512KX32 SRAM PLASTIC TQFP 3.3V |
| MT58L512Y32DT-6 | 制造商:Cypress Semiconductor 功能描述:DS2KX32 SRAM PLASTIC TQFP 3.3V 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MT58L512Y32PT-10 IT | 制造商:Cypress Semiconductor 功能描述:16MB 512KX32 SRAM PLASTIC IND |
| MT58L512Y32PT-6 | 制造商:Cypress Semiconductor 功能描述:512KX32 SRAM PLASTIC TQFP 3.3V |
發布緊急采購，3分鐘左右您將得到回復。