- 您現在的位置：買賣IC網 > PDF目錄385639 > MT28F320A18 (Micron Technology, Inc.) FLASH MEMORY PDF資料下載
參數資料
| 型號： | MT28F320A18 |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | FLASH MEMORY |
| 中文描述： | 閃存 |
| 文件頁數： | 17/37頁 |
| 文件大小： | 558K |
| 代理商： | MT28F320A18 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
2 MEG x 16
1.8V ENHANCED+ BOOT BLOCK FLASH MEMORY
PRELIMINARY
2 Meg x 16, 1.8V Enhanced+ Boot Block Flash Memory
MT28F320A18_3.fm - Rev. 3, Pub. 9/2002
2002, Micron Technology Inc.
17
BLOCK LOCKING
The MT28F320A18 Flash memory provides a flexible
locking scheme that allows each block to be individu-
ally locked or unlocked with no latency.
The device offers two-level protection for the
blocks. The first level allows software-only control of
block locking (for data that needs to be changed fre-
quently), while the second level requires hardware
interaction before locking can be changed (code that
does not require frequent updates). Control pins WP#,
DQ1, and DQ0 define the state of a block; for example,
state [001] means WP# = 0, DQ1 = 0 and DQ0 = 1.
Table 9 defines all of the possible locking states.
Note:
All blocks are software-locked upon power-
up sequence completion.
Locking operation
The following summarizes the locking operation.
1. All blocks are locked on power-up. They can then be
unlocked or locked down with the UNLOCK and
LOCK DOWN commands.
2. The LOCK DOWN command locks a block and pre-
vents it from being unlocked when WP# = 0.
When WP# = 1, lock down is overridden. Com-
mands can then unlock/lock locked down blocks.
When WP# returns to 0, locked down blocks
return to lock down.
Lock down is cleared only when the device is
reset or powered down.
Locked State
After a power-up sequence completion, or after a
reset sequence, all blocks are locked (states [001] or
[101]). This means full protection from alteration. Any
PROGRAM or ERASE operations attempted on a
locked block will return an error on bit SR1 of the sta-
tus register. The status of a locked block can be
changed to unlocked or lock down using the appropri-
ate software commands. Writing the lock command
sequence, 60h followed by 01h, can lock an unlocked
block.
Unlocked State
Unlocked blocks (states [000], [100], [110]) can be
programmed or erased. All unlocked blocks return to
the locked state when the device is reset or powered
down. An unlocked block can be locked or locked
down using the appropriate software command
sequence (see Table 4).
Locked Down State
Blocks that are locked down (state [011]) are pro-
tected from PROGRAM and ERASE operations, but
their protection status cannot be changed using soft-
ware commands alone. A locked or unlocked block can
be locked down by writing the lock down command
sequence, 60h followed by 2Fh. Locked down blocks
revert to the locked state when the device is reset or
powered down.
The lock down function is dependent on the WP#
input pin. When WP# = 0, blocks in lock down [011] are
protected from program, erase and lock status
changes. When WP# = 1, the lock down function is dis-
abled ([111]) and locked down blocks can be individu-
ally unlocked by a software command to the [110]
state, where they can be erased and programmed.
These blocks can then be relocked [111] and unlocked
[110] as desired as long as WP# remains HIGH. When
WP# goes LOW, blocks that were previously locked
down return to the locked down state [011] regardless
of any changes made while WP# was HIGH. Device
reset or power-down resets all locked blocks, including
those in lock down, to locked state (see Table 9).
Reading a Block’s Lock Status
The lock status of every block can be read in the
read device identification mode. To enter this mode,
write 90h to the device. Subsequent READs at block
address + 00002h will output the lock status of that
block. The lowest two outputs, DQ0 and DQ1, repre-
sent the lock status. DQ0 indicates the block lock/
unlock status and is set by the LOCK command and
cleared by the UNLOCK command. It is also automati-
cally set when entering lock down. DQ1 indicates lock
down status and is set by the LOCK DOWN command.
It can only be cleared by reset or power-down, not by
software. Table 9 shows the locking state transition
scheme.
Locking Operations during Erase
Suspend
Changes to block lock status can be performed dur-
ing an ERASE SUSPEND by using the standard locking
command sequences to unlock, lock, or lock down.
This is useful in the case when another block needs to
be updated while an ERASE operation is in progress.
To change block locking during an ERASE opera-
tion, first write the ERASE SUSPEND command (B0h),
then check the status register until it indicates that the
ERASE operation has been suspended. Next, write the
desired lock command sequence to block lock, and the
相關PDF資料 |
PDF描述 |
|---|---|
| MT2D18 | 1 Meg x 8 DRAM Module(5V，1M x 8 動態RAM模塊) |
| MT46V16M4 | 4 Meg x 4 x 4 banks DDR SDRAM(4 M x 4 x 4組，雙數據速率同步動態RAM) |
| MT46V4M16 | 1 Meg x 16 x 4 banks DDR SDRAM(1M x 16 x 4組，雙數據速率同步動態RAM) |
| MT46V8M8 | 2 Meg x 8 x 4 banks DDR SDRAM(2 M x 8 x 4組，雙數據速率同步動態RAM) |
| MT46V2M32LG | DOUBLE DATA RATE DDR SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT28F320J3 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Q-FLASHTM MEMORY |
| MT28F320J3BS-11 ET | 功能描述:IC FLASH 32MBIT 110NS 64FBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869 |
| MT28F320J3BS-11 ET TR | 功能描述:IC FLASH 32MBIT 110NS 64FBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:378 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:8M（1M x 8，512K x 16） 速度:110ns 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-CBGA 供應商設備封裝:48-CBGA（7x7） 包裝:托盤 |
| MT28F320J3BS-11 GMET | 功能描述:IC FLASH 32MBIT 110NS 64FBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869 |
| MT28F320J3BS-11 GMET TR | 功能描述:IC FLASH 32MBIT 110NS 64FBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:378 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:8M（1M x 8，512K x 16） 速度:110ns 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-CBGA 供應商設備封裝:48-CBGA（7x7） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。