參數資料
型號： MC9RS08KA1CSCR
廠商： Freescale Semiconductor
文件頁數： 92/136頁
文件大小： 0K
描述： IC MCU 8-BIT 1K FLASH 8-SOIC
產品培訓模塊： Mechatronics
USBSpyder08 Discovery Kit
RS08KA2 Low-End Microcontroller Series
MC9RS08KA8 Microcontroller
標準包裝： 1
系列： RS08
核心處理器： RS08
芯體尺寸： 8-位
速度： 10MHz
外圍設備： LVD，POR，WDT
輸入/輸出數： 4
程序存儲器容量： 1KB（1K x 8）
程序存儲器類型： 閃存
RAM 容量： 63 x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
包裝： 標準包裝
產品目錄頁面： 726 (CN2011-ZH PDF)
其它名稱： MC9RS08KA1CSCRDKR
Chapter 8 Central Processor Unit (RS08CPUV1)
MC9RS08KA2 Series Data Sheet, Rev. 4
Freescale Semiconductor
59
8.2.2
Program Counter (PC)
The program counter is a 14-bit register that contains the address of the next instruction or operand to be
fetched.
During normal execution, the program counter automatically increments to the next sequential memory
location each time an instruction or operand is fetched. Jump, branch, and return operations load the
program counter with an address other than that of the next sequential location. This is called a
change-of-flow.
During reset, the program counter is loaded with $3FFD and the program will start execution from this
specific location.
8.2.3
Shadow Program Counter (SPC)
The shadow program counter is a 14-bit register. During a subroutine call using either a JSR or a BSR
instruction, the return address will be saved into the SPC. Upon completion of the subroutine, the RTS
instruction will restore the content of the program counter from the shadow program counter.
During reset, the shadow program counter is loaded with $3FFD.
8.2.4
Condition Code Register (CCR)
The 2-bit condition code register contains two status flags. The content of the CCR in the RS08 is not
directly readable. The CCR bits can be tested using conditional branch instructions such as BCC and BEQ.
These two register bits are directly accessible through the BDC interface. The following paragraphs
provide detailed information about the CCR bits and how they are used. Figure 8-3 identifies the CCR bits
and their bit positions.
Figure 8-3. Condition Code Register (CCR)
The status bits (Z and C) are cleared to 0 after reset.
The two status bits indicate the results of arithmetic and other instructions. Conditional branch instructions
will either branch to a new program location or allow the program to continue to the next instruction after
the branch, depending on the values in the CCR status bit. Conditional branch instructions, such as BCC,
BCS, and BNE, cause a branch depending on the state of a single CCR bit.
Often, the conditional branch immediately follows the instruction that caused the CCR bit(s) to be updated,
as in this sequence:
cmp
#5
;compare accumulator A to 5
blo
lower
;branch if A smaller 5
more:
deca
;do this if A not higher than or same as 5
lower:
CARRY
ZERO
CCR
C
Z
CONDITION CODE REGISTER
相關PDF資料
PDF描述
V24A28T400B3 CONVERTER MOD DC/DC 28V 400W
MC9S12HZ64CAA IC MCU 16BIT 64K FLASH 80-QFP
2-6457567-5 ADPTR,DUP,LC,SR BEIGE,CER,LOGO
V24A28T400B CONVERTER MOD DC/DC 28V 400W
MC908MR8MPE IC MCU 8BIT 8K FLASH 28-PDIP
相關代理商/技術參數
參數描述
MC9RS08KA1DB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC9RS08KA1PC 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC9RS08KA1SC 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC9RS08KA2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC9RS08KA2_07 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*