參數資料
型號： MC68302PV33C
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP144
封裝： 20 X 20 MM, 1.40 MM HEIGHT, 0.50 MM PITCH, PLASITC, LQFP-144
文件頁數： 51/128頁
文件大?。?/td> 641K
代理商： MC68302PV33C
MC68EN302 Module Bus Controller
2-12
MC68EN302 REFERENCE MANUAL
MOTOROLA
2.10.4 Parity Pin Enable
During hardware reset, the parity pin enable bit (PPE) in the MBC register (see 2.4 Module
Bus Control (MBCTL)) is cleared, which results in the parity pins becoming inputs. Each of
the three pins is sampled for a different function, as shown in Table 2-5. After exiting
hardware reset, these pins are sampled to determine chip functions. Pullup or pulldown
resistors are required for presetting the desired state if the parity pins are to be later
programmed as input/output pins. After hardware reset, the PPE bit can be set to enable the
parity pins as outputs. The PPE bit should be set to enable parity even on reads.
2.11 INTERRUPT SUPPORT
All module bus and module bus controller interrupts are at level 5 or at level 3 if MIL is set
(See 2.5 Interrupt Extension Register (IER)). There are two sources of interrupts in the MBC:
One is the Ethernet controller; the second source is the parity error interrupt. The parity error
interrupt is the higher priority of the two. If an interrupt acknowledge cycle is generated when
both interrupts are asserted, the MBC responds to the parity error interrupt by driving its
vector onto the internal 68000 bus. Only after the parity error interrupt is cleared will the
Ethernet controller respond to an IACK cycle.
In order to accommodate an additional interrupt source within the MC68EN302, an
additional Interrupt Mode (IMOD) bit is provided in the MBC. This bit configures the Interrupt
pins as IRQ or IPL lines. This replaces the MOD bit in the Global Interrupt Mode Register
(GIMR). This means that the existing MOD bit in the Global Interrupt Mode Register (GIMR)
must always remain at zero. The IMOD bit in the IER register duplicates this function in the
MBC.
Since the MBC generates a level 5 (or level 3) interrupt, and there is no way to resolve IACK
conflicts with the external circuitry, a level 5 (or level 3) interrupt should not be asserted
externally. Figure 2-8 summarizes the interrupt configuration and priorities.
Table 2-5. Parity Pin Enable Operation
PPE = 0
PIN FUNCTION
PPE = 1
PIN FUNCTION
DISCPU
PARITY0
BUSW
PARITY1
THREES
PARITYE
相關PDF資料
PDF描述
SPAK302PV16VC 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP144
SPAK302FC25C 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP132
MC68EN360EM25 7 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP240
MC68EN360FE33 RISC MICROCONTROLLER, CQFP240
MC68360RC25 RISC MICROCONTROLLER, CPGA241
相關代理商/技術參數
參數描述
MC68302RC16 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Multiprotocol Processor User’s Manual
MC68302RC16C 功能描述:微處理器 - MPU 68K INTGR COM PROC DMA RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC68302RC20 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Multiprotocol Processor User’s Manual
MC68302RC20C 功能描述:微處理器 - MPU 68K INTGR COM PROC DMA RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC68302RC25 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Multiprotocol Processor User’s Manual
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*