- 您現在的位置：買賣IC網 > PDF目錄45193 > MB91F467PAPMC-GSE2 (FUJITSU LTD) RISC MICROCONTROLLER, PQFP176 PDF資料下載
參數資料
| 型號： | MB91F467PAPMC-GSE2 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | RISC MICROCONTROLLER, PQFP176 |
| 封裝： | 24 X 24 MM, 0.50 MM PITCH, LEAD FREE, PLASTIC, LQFP-176 |
| 文件頁數： | 162/200頁 |
| 文件大?。?/td> | 6566K |
| 代理商： | MB91F467PAPMC-GSE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁當前第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
MB91460P Series
64
DS07-16615-2E
■ HANDLING DEVICES
1.
Preventing Latch-up
Latch-up may occur in a CMOS IC if a voltage higher than (VDD5, VDD35 or HVDD5 *1) or less than (VSS5 or
HVSS5 *1) is applied to an input or output pin or if a voltage exceeding the rating is applied between the power
supply pins and ground pins. If latch-up occurs, the power supply current increases rapidly, sometimes resulting
in thermal breakdown of the device. Therefore, be very careful not to apply voltages in excess of the absolute
maximum ratings.
Note *1: HVDD5, HVSS5 are available only on devices having Stepper Motor Controller.
2.
Handling of unused input pins
If unused input pins are left open, abnormal operation may result. Any unused input pins should be connected
to pull-up or pull-down resistor (2K
Ω to 10KΩ) or enable internal pullup or pulldown resisters (PPER/PPCR)
before the input enable (PORTEN) is activated by software. The mode pins MD_x can be connected to VSS5 or
VDD5 directly. Unused ALARM input pins can be connected to AVSS5 directly.
3.
Power supply pins
In MB91460 series, devices including multiple power supply pins and ground pins are designed as follows; pins
necessary to be at the same potential are interconnected internally to prevent malfunctions such as latch-up.
All of the power supply pins and ground pins must be externally connected to the power supply and ground
respectively in order to reduce unnecessary radiation, to prevent strobe signal malfunctions due to the ground
level rising and to follow the total output current ratings. Furthermore, the power supply pins and ground pins of
the MB91460 series must be connected to the current supply source via a low impedance.
It is also recommended to connect a ceramic capacitor of approximately 0.1
μF as a bypass capacitor between
power supply pin and ground pin near this device.
This series has a built-in step-down regulator. Connect a bypass capacitor of 4.7
μF (use a X7R ceramic
capacitor) to VCC18C pin for the regulator.
4.
Crystal oscillator circuit
Noise in proximity to the X0 (X0A) and X1 (X1A) pins can cause the device to operate abnormally. Printed circuit
boards should be designed so that the X0 (X0A) and X1 (X1A) pins, and crystal oscillator, as well as bypass
capacitors connected to ground, are located near the device and ground.
It is recommended that the printed circuit board layout be designed such that the X0 and X1 pins or X0A and
X1A pins are surrounded by ground plane for the stable operation.
Please request the oscillator manufacturer to evaluate the oscillational characteristics of the crystal and this
device.
5.
Notes on using external clock
When using the external clock, it is necessary to simultaneously supply the X0 (X0A) and the X1 (X1A) pins. In
the described combination, X1 (X1A) should be supplied with a clock signal which has the opposite phase to
the X0 (X0A) pins. At X0 and X1, a frequency up to 16 MHz is possible.
(Continued)
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F469GBPB-GS | 32-BIT, FLASH, 88 MHz, RISC MICROCONTROLLER, PBGA320 |
| MB91F469GAPB-GS | 32-BIT, FLASH, 88 MHz, RISC MICROCONTROLLER, PBGA320 |
| MB91F469QAPB-GSE1 | RISC MICROCONTROLLER, PBGA320 |
| MB91F469TAPMC-GSE2 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
| MB91F467TAPMC-GSE2 | 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F467R | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91F467RCPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB91F467RCPMC-GSE1 | 制造商:FUJITSU 功能描述: |
| MB91F467RDPMC-ESE2 | 制造商:FUJITSU 功能描述: |
| MB91F467RDPMC-GSE2 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。