SPI/I2C UART with 128-Word FIFOs Multidrop Mode In multidrop mode, also known as" />
參數資料
型號： MAX3107EVKIT+
廠商： Maxim Integrated Products
文件頁數： 11/52頁
文件大小： 0K
描述： EVAL KIT I2C/SPI UART MAX3107
產品培訓模塊： Obsolescence Mitigation Program
標準包裝： 1
主要目的： 接口，UART
已用 IC / 零件： MAX3107
主要屬性： 圖形用戶界面（GUI）
次要屬性： I²C & SPI 接口
已供物品： 板，線纜
SPI/I2C UART with 128-Word FIFOs
Multidrop Mode
In multidrop mode, also known as 9-bit mode, the word
length is 8 bits and a 9th bit is used for distinguishing
between an address and a data word. Multidrop mode is
enabled through MODE2[6]: MultiDrop. Parity checking
is disabled and an SpclCharInt[5]: MultiDropInt interrupt
is generated when an address (9th bit set) is received.
It is up to the host processor to filter out the data intend-
ed for its address. Alternatively, the auto data-filtering
mode can be used to automatically filter out the data
intended for the station’s specific 9-bit mode address.
Auto Data Filtering in Multidrop Mode
In multidrop mode, the MAX3107 can be configured
to automatically filter out data that is not meant for its
address. The address is user-definable either by pro-
gramming a register value or a combination of a register
values and GPIO hardware inputs. Use either XOFF2
or XOFF2[7:4] in combination with GPIO_ to define the
address.
Enable multidrop mode by setting MODE2[6]: MultiDrop
to 1 and enable auto data filtering by setting MODE2[4]:
SpecialChr to 1.
When using register bits in combination with GPIO_ to
define the address, the MSB of the address is written to
XOFF2[7:4] register bits, while the LSBs of the address
are defined through the GPIOs. To enable this mode,
set FlowCtrl[2]: GPIAddr, MODE2[4]: SpecialChr, and
MODE2[6]: MultiDrop to 1. GPIO_ is automatically read
when FlowCtrl[2]: GPIAddr is set to 1, and the address
is updated on logic changes at GPIO_.
In the auto data-filtering mode, the MAX3107 auto-
matically accepts data that is meant for its address and
places this into the receive FIFO, while it discards data
that is not meant for its address. The received address
word is not put into the FIFO.
Auto Transceiver Direction Control
In some half-duplex communication systems, the trans-
ceiver’s transmitter must be turned off when data is
being received so as not to load the bus. This is the
case in half-duplex RS-485 communication. Similarly
in full-duplex multidrop communication, like RS-485 or
RS-422/V.11, only one transmitter can be enabled at any
one time and the others must be disabled. The MAX3107
can automatically enable/disable a transceiver’s trans-
mitter and/or receiver. This relieves the host processor
of this time-critical task.
The RTS/CLKOUT output is used to control the transceiv-
ers’ transmit enable input and is automatically set high
when the MAX3107’s transmitter starts transmission.
This occurs as soon as data is present in the transmit
FIFO. Auto transceiver direction control is enabled
through MODE1[4]: TrnscvCtrl. Figure 9 shows a typical
MAX3107 connection in a RS-485 application.
The RTS/CLKOUT output can be set high in advance
of TX transmission by a programmable time period
called the setup time (Figure 10). The setup time is pro-
grammed through HDplxDelay[7:4]. Similarly, the RTS/
CLKOUT signal can be held high for a programmable
period after the transmitter has completed transmission.
The hold time is programmed through HDplxDelay[3:0].
Figure 9. Auto Transceiver Direction Control
MAX3107
MAX13431
TRANSMITTER
TX
B
A
D
RTS/CLKOUT
RX
TxFIFO
RECEIVER
AUTO
TRANSCEIVER
CONTROL
RxFIFO
DI
RO
RE
DE
R
Maxim Integrated
19
MAX3107
相關PDF資料
PDF描述
GBB22DHLT CONN EDGECARD 44POS .050 DIP SLD
CGS902U040R4C CAP ALUM 9000UF 40V SCREW
A3AAH-6436M IDC CABLE - ASC64H/AE64M/ASC64H
GBB30DHNN CONN EDGECARD 60POS .050 DIP SLD
383LX152M450B102VS CAP ALUM 1500UF 450V 20% SNAP
相關代理商/技術參數
參數描述
MAX3107EVKIT+ 功能描述:UART 接口集成電路 UART with integrated Oscillator RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3108AEWA+ 制造商:Maxim Integrated Products 功能描述:LOW SHUTDOWN CURRENT SPI/I?C UART WITH 128-WORD FIFOS IN WLP - Rail/Tube
MAX3108AEWA+T 功能描述:UART 接口集成電路 SPI/I2C UART W/ 128 WORD FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3108EWA+ 制造商:Maxim Integrated Products 功能描述:SPI/IAC UART WITH 128-WORD FIFOS IN WLP - Rail/Tube
MAX3108EWA+T 功能描述:IC UART RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:* 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*