- 您現在的位置：買賣IC網 > PDF目錄45047 > M38C24M4A-XXXFP 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38C24M4A-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 5 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 53/102頁 |
| 文件大?。?/td> | 1369K |
| 代理商： | M38C24M4A-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
Rev.2.00
May 28, 2004
page 54 of 100
38C2 Group (A Version)
NOTES ON USE
VL3 pin
When LCD drive control circuit is not used, connect VL3 to VCC.
Countermeasures against noise
(1) Shortest wiring length
Wiring for RESET pin
Make the length of wiring which is connected to the RESET pin as
short as possible. Especially, connect a capacitor across the
RESET pin and the VSS pin with the shortest possible wiring (within
20mm).
q Reason
The width of a pulse input into the RESET pin is determined by
the timing necessary conditions. If noise having a shorter pulse
width than the standard is input to the RESET pin, the reset is
released before the internal state of the microcomputer is com-
pletely initialized. This may cause a program runaway.
Fig. 57 Wiring for clock I/O pins
(2) Connection of bypass capacitor across VSS line and VCC line
Connect an approximately 0.1
F bypass capacitor across the VSS
line and the VCC line as follows:
Connect a bypass capacitor across the VSS pin and the VCC pin at
equal length.
Connect a bypass capacitor across the VSS pin and the VCC pin
with the shortest possible wiring.
Use lines with a larger diameter than other signal lines for VSS line
and VCC line.
Connect the power source wiring via a bypass capacitor to the VSS
pin and the VCC pin.
Fig. 56 Wiring for the RESET pin
Wiring for clock input/output pins
Make the length of wiring which is connected to clock I/O pins as
short as possible.
Make the length of wiring (within 20 mm) across the grounding
lead of a capacitor which is connected to an oscillator and the
VSS pin of a microcomputer as short as possible.
Separate the VSS pattern only for oscillation from other VSS pat-
terns.
q Reason
If noise enters clock I/O pins, clock waveforms may be deformed.
This may cause a program failure or program runaway. Also, if a
potential difference is caused by the noise between the VSS level
of a microcomputer and the VSS level of an oscillator, the correct
clock will not be input in the microcomputer.
RESET
Reset
circuit
Noise
VSS
Reset
circuit
VSS
RESET
VSS
N.G.
O.K.
Fig. 58 Bypass capacitor across the VSS line and the VCC line
Noise
XIN
XOUT
VSS
XIN
XOUT
VSS
N.G.
O.K.
VSS
VCC
VSS
VCC
N.G.
O.K.
相關PDF資料 |
PDF描述 |
|---|---|
| M38C24M6-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C29MC-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M6-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M4-XXXHP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C24M4-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38C24M4-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M4-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-051HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。