參數資料
型號： M37920FCCGP
廠商： Mitsubishi Electric Corporation
英文描述： Single Chip 16 Bits CMOS Microcomputer(16位單片機)
中文描述： 單片微機16位的CMOS（16位單片機）
文件頁數： 128/158頁
文件大小： 1261K
代理商： M37920FCCGP
M37920FCCGP, M37920FCCHP
M37920FGCGP, M37920FGCHP
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
MITSUBISHI MICROCOMPUTERS
128
Busy
Terminated normally.
Terminated normally.
Terminated normally.
Ready
Terminated by error.
Terminated by error.
Terminated by error.
Table 27. Bit definition of status register
SR.7 (D
7
)
SR.6 (D
6
)
SR.5 (D
5
)
SR.4 (D
4
)
SR.3 (D
3
)
SR.2 (D
2
)
SR.1 (D
1
)
SR.0 (D
0
)
Write State Machine (WSM) Status
Reserved
Erase Status
Programming Status
Block Status After Programming
Reserved
Reserved
Reserved
Symbol
Status
Definition
“
1
”
“
0
”
Write State Machine (WSM) Status Bit (SR.7)
This bit reports the operation status of the WSM. This bit is set to
“
1
”
(READY) after the system power is turned on or after reset is re-
moved.
During the automatic programming or erase operation, this bit is
cleared to
“
0
”
(BUSY), however, set to
“
1
”
upon completion of them.
Erase Status Bit (SR.5)
This bit reports the status of the automatic erase operation. This bit
is set to
“
1
”
if an erase error occurs and returns to
“
0
”
if one of the
following conditions is satisfied:
the system power is turned on.
reset is removed.
the clear status register command (50
16
) is executed.
Programming Status Bit (SR.4)
This bit reports the status of the automatic programming operation.
This bit is set to
“
1
”
if a programming error occurs and returns to
“
0
”
if one of the following conditions is satisfied:
the system power is turned on.
reset is removed.
the clear status register command (50
16
) is executed.
Block Status After Programming Bit (SR.3)
This bit is set to
“
1
”
, upon completion of the page programming op-
eration, if the excessive programming
(Note)
occurs. That is, the sta-
tus register becomes
“
80
16
”
when the programming operation is
terminated normally,
“
90
16
”
when the programming operation is
failed, and
“
88
16
”
when the excessive programming occurs.
Under the condition that any of SR.5, SR.4 and SR.3 =
“
1
”
, none of
the page programming, block erase, erase all unlocked block, and
lock bit programming commands can be accepted. To execute these
commands, in advance, execute the clear status register command
(50
16
) to clear the status register.
Both of SR.4 and SR.5 are set to
“
1
”
under the following conditions
(Command Sequence Error):
(1) when data other than
“
D0
16
”
and
“
FF
16
”
is written to the data in
the 2nd bus cycle of the lock bit programming command (77
16
/
D0
16
)
(2) when data other than
“
D0
16
”
and
“
FF
16
”
is written to the data in
the 2nd bus cycle of the block erase command (20
16
/D0
16
)
(3) when data other than
“
D0
16
”
and
“
FF
16
”
is written to the data in
the 2nd bus cycle of the erase all unlocked block command
(A7
16
/D0
16
)
Note that, writing of
“
FF
16
”
forces the microcomputer into the read
array mode. Simultaneously with this, the command written in the 1st
bus cycle will be canceled.
Note:
The excessive programming means the status that memory
cells are too depleted, so data cannot be read out correctly.
Full Status Check
The full status check reports the results of the erase or programming
operation.
Figure 126 shows the full status check flowchart and actions to be
taken if an error has occurred.
相關PDF資料
PDF描述
M37920FCCHP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37920FGCHP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M3802 Single Chip 8 Bits Microcomputer(8位單片機)
M3820 Single Chip 8 Bits Microcomputer(8位單片機)
M3822 Single Chip 8 Bits Microcomputer(8位單片機)
相關代理商/技術參數
參數描述
M37920FCCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920FGCGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37920S4CGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37P75C4P3 功能描述:汽車連接器 Pin Contact RoHS:否 制造商:Amphenol SINE Systems 產品:Contacts 系列:ATP 位置數量: 型式:Female 安裝風格: 端接類型: 觸點電鍍:Nickel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*