- 您現在的位置：買賣IC網 > PDF目錄98007 > M37902FGCHP 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M37902FGCHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 117/143頁 |
| 文件大?。?/td> | 1148K |
| 代理商： | M37902FGCHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁當前第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁
75
M37902FCCHP, M37902FGCHP, M37902FJCHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
The FERi, PERi, and SUMi flags are cleared to “0” when reading the
low-order byte of the receive buffer register or when writing “0” to the
REi flag.
The OERi flag is cleared to “0” when writing “0” to the REi flag.
Interrupt request at completion of reception
When the RIk flag changes from “0” to “1”, in other words, when the
receive operation is completed, the interrupt request bit of the
UARTk receive interrupt control register can be set to “1”.
The timing when this interrupt request bit is to be set to “1” can be
selected from the following:
Each reception
When an error occurs at reception
If bit 5 of the UARTk transmit/receive control register 0 (UART re-
ceive interrupt mode select bit) is cleared to “0”, the interrupt request
bit is set to “1” at each reception. If bit 5 is set to “1”, the interrupt
request bit is set to “1” only when an error occurs. (In the clock asyn-
chronous serial communication, when an overrun error, framing er-
ror, or parity error occurs, the interrupt request bit is set to “1”.)
Sleep mode
The sleep mode is used to communicate only between certain micro-
computers when multiple microcomputers are connected through
serial I/O.
The microcomputer enters the sleep mode when bit 7 of UARTi
transmit/receive mode register is set to “1.”
The operation of the sleep mode for an 8-bit asynchronous commu-
nication is described below.
When sleep mode is selected, the contents of the receive register is
not transferred to the receive buffer register if bit 7 (bit 6 if 7-bit asyn-
chronous communication and bit 8 if 9-bit asynchronous communi-
cation) of the received data is “0”. Also the RIi, OERi, FERi, PERi,
and the SUMi flags are unchanged. Therefore, the interrupt request
bit of the UARTi receive interrupt control register is also unchanged.
Normal receive operation takes place when bit 7 of the received data
is “1”.
The following is an example of how the sleep mode can be used.
The main microcomputer first sends data: bit 7 is “1” and bits 0 to 6
are set to the address of the subordinate microcomputer to be com-
municated with. Then all subordinate microcomputers receive this
data. Each subordinate microcomputer checks the received data,
clears the sleep bit to “0” if bits 0 to 6 are its own address and sets
the sleep bit to “1” if not. Next, the main microcomputer sends data
with bit 7 cleared. Then the microcomputer which cleared the sleep
bit will receive the data, but the microcomputers which set the sleep
bit to “1” will not. In this way, the main microcomputer is able to com-
municate only with the designated microcomputer.
Precautions for clock asynchronous (UART)
serial communication
________ ________
When using pin CTS0/RTS0, be sure to clear the D-A2 output enable
_______
bit (bit 2 at address 9616) to “0” (output disabled). Also, when CTSi
_______
and RTSi are separated, pin CLKi cannot be used. Therefore, when
_______
CTSi and RTSi are separated in UART mode, be sure to select an
internal clock.
Before transmit operation is performed, be sure to clear bits 2 and 3
of the serial I/O pin control register (address AC16) to “00”.
相關PDF資料 |
PDF描述 |
|---|---|
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37906F8CFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42 |
| M37906F8CSP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
| M38184E8-XXXFP | 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37902FJCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37903S4CHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905F8CFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905F8CSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37905M4C | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。