參數資料
型號: M37641F8FP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80
封裝: 14 X 20 MM, 0.80 MM, PLASTIC, QFP-80
文件頁數: 80/140頁
文件大小: 1694K
代理商: M37641F8FP
7641 Group
Rev.4.00
Aug 28, 2006
page 42 of 135
REJ03B0191-0400
(2) Burst Transfer Mode
When the DMAC Channel x Transfer Mode Selection Bit (DxTMS)
is set to “1”, the respective DMAC channel operates in the burst
transfer mode.
In the burst transfer mode, the DMAC continually transfers the
number of bytes of data specified by the Transfer Count Register
for one transfer request. Other than this, the burst transfer mode
operation is the same as the cycle steal mode operation.
Priority
The DMAC places a higher priority on Channel-0 transfer requests
than on Channel-1 transfer requests.
If a Channel-0 transfer request occurs during a Channel-1 burst
transfer operation, the DMAC completes the next transfer source
and destination read/write operation first, and then starts the
Channel-0 transfer operation. As soon as the Channel-0 transfer is
completed, the DMAC resumes the Channel-1 transfer operation.
When an interrupt request occurs during any DMA operation, the
transfer operation is suspended and the interrupt process routine
is initiated. During the interrupt operation, the DMAC automatically
sets the corresponding DMAC Channel x (x = 0, 1) Suspend Flag
(DxSFI) to “1”. As soon as the CPU completes the interrupt opera-
tion, the DMAC clears the flag to “0” and resumes the original
operation from the point where it was suspended.
The suspended transfer due to the interrupt can also be resumed
during its interrupt process routine by writing “1” to the DMAC
Channel x (x = 0,1) Enable Bit (DxCEN).
The timing charts for a burst transfer caused by a hardware-re-
lated transfer request are shown in Figure 35.
Fig. 35 Timing chart for burst transfer caused by hardware-related transfer request
A5
ADL185
PC + 2
ADL1, 00
PC + 1
PC
PC + 3
LDA $zz
STA $zz
(First cycle)
STA $zz
(Second cycle)
φ
OUT
SYNCOUT
RD
WR
DMAOUT
(Port P33)
Address
Data
Transfer request
source (“L” active)
Transfer request source
sampling
Reset of transfer request
source sampling
DMA transfer
Data
DMA destina-
tion add. 1
DMA source
add. 1
DMA destina-
tion add. 2
DMA source
add. 2
DMA
data 1
DMA
data 1
DMA
data 2
DMA
data 2
ADL2
相關PDF資料
PDF描述
M37641M8-XXXFP 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
M37643M8-XXXFP 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M37643F8HP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80
M37643M8-XXXHP 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M37700M2-XXXFP 16-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M37641F8FP#U0 功能描述:IC 740 MCU FLASH 32K 80QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/7600 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
M37641F8HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8HP#U0 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/7600 產品培訓模塊:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 標準包裝:27 系列:PIC® 24H 核心處理器:PIC 芯體尺寸:16-位 速度:40 MIP 連通性:I²C,SPI,UART/USART 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:21 程序存儲器容量:12KB(4K x 24) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 3.6 V 數據轉換器:A/D 10x10b/12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 包裝:管件 產品目錄頁面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
M37641F8M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER