- 您現在的位置：買賣IC網 > PDF目錄369814 > LPC2917 (NXP Semiconductors N.V.) ARM9 microcontroller with CAN and LIN PDF資料下載
參數資料
| 型號： | LPC2917 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 32位微控制器 |
| 英文描述： | ARM9 microcontroller with CAN and LIN |
| 中文描述： | 具有CAN和LIN的ARM9微控制器 |
| 文件頁數： | 15/68頁 |
| 文件大?。?/td> | 384K |
| 代理商： | LPC2917 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
DRAFTDRAFTDRAFTDRAFTDRAFTDRAFTD
LPC2917_19_1
NXP B.V. 2007. All rights reserved.
Preliminary data sheet
Rev. 1.01 — 15 November 2007
15 of 68
NXP Semiconductors
LPC2917/19
ARM9 microcontroller with CAN and LIN
The flash memory has a 128-bit wide data interface and the flash controller offers two
128-bit buffer lines to improve system performance. The flash has to be programmed
initially via JTAG. In-system programming must be supported by the boot loader.
In-application programming is possible. Flash memory contents can be protected by
disabling JTAG access. Suspension of burning or erasing is not supported.
The key features are:
Programming by CPU via AHB
Programming by external programmer via JTAG
JTAG access protection
Burn-finished and erase-finished interrupt
8.1.2
Description
After reset flash initialization is started, which takes t
init
time, see
Section 12
. During this
initialization flash access is not possible and AHB transfers to flash are stalled, blocking
the AHB bus.
During flash initialization the index sector is read to identify the status of the JTAG access
protection and sector security. If JTAG access protection is active the flash is not
accessible via JTAG. ARM debug facilities are disabled to protect the flash-memory
contents against unwanted reading out externally. If sector security is active only the
concerned sections are read.
Flash can be read synchronously or asynchronously to the system clock. In synchronous
operation the flash goes into standby after returning the read data. Started reads cannot
be stopped, and speculative reading and dual buffering are therefore not supported.
With asynchronous reading, transfer of the address to the flash and of read data from the
flash is done asynchronously, giving the fastest possible response time. Started reads can
be stopped, so speculative reading and dual buffering are supported.
Buffering is offered because the flash has a 128-bit wide data interface while the AHB
interface has only 32 bits. With buffering a buffer line holds the complete 128-bit flash
word, from which four words can be read. Without buffering every AHB data port read
starts a flash read. A flash read is a slow process compared to the minimum AHB cycle
time, so with buffering the average read time is reduced. This can improve system
performance.
With single buffering the most recently read flash word remains available until the next
flash read. When an AHB data-port read transfer requires data from the same flash word
as the previous read transfer, no new flash read is done and the read data is given without
wait cycles.
When an AHB data-port read transfer requires data from a different flash word to that
involved in the previous read transfer, a new flash read is done and wait states are given
until the new read data is available.
With dual buffering a secondary buffer line is used, the output of the flash being
considered as the primary buffer. On a primary buffer hit data can be copied to the
secondary buffer line, which allows the flash to start a speculative read of the next flash
word.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2919 | ARM9 microcontroller with CAN and LIN |
| LPC3180 | 16/32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface |
| LPC61W26X | Microcontroller |
| LPC61W49X | Microcontroller |
| LPC660AIMX | Voltage-Feedback Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2917/01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN and LIN |
| LPC2917FBD144 | 制造商:NXP Semiconductors 功能描述:IC MCU 32BIT ARM968 SMD LQFP144 |
| LPC2917FBD144,551 | 功能描述:ARM微控制器 - MCU ARM968 512K FL/48K RAM LIN 2.0 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2917FBD144/01 | 制造商:NXP Semiconductors 功能描述:MCU, 32BIT, ARM968E-S, 125MHZ, LQFP-144 制造商:NXP Semiconductors 功能描述:MCU, 32BIT, ARM968E-S, 125MHZ, LQFP-144, Controller Family/Series:LPC2900, Core Size:32bit, No. of I/O's:108, Supply Voltage Min:1.71V, Supply Voltage Max:1.89V, Digital IC Case Style:LQFP, No. of Pins:144, Program Memory Size:512KB, |
| LPC2917FBD144/01/, | 功能描述:ARM微控制器 - MCU ARM968 512K FL/48K RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。