- 您現在的位置：買賣IC網 > PDF目錄369814 > LPC2460 (NXP Semiconductors N.V.) Flashless 16-bit/32-bit micro; Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface PDF資料下載
參數資料
| 型號： | LPC2460 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Flashless 16-bit/32-bit micro; Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface |
| 中文描述： | 毛邊16-bit/32-bit微，以太網，CAN，供應商/國際檢察官聯合會，USB 2.0設備/主機/ OTG功能，外部存儲器接口 |
| 文件頁數： | 43/67頁 |
| 文件大?。?/td> | 340K |
| 代理商： | LPC2460 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
LPC2460_0
NXP B.V. 2007. All rights reserved.
Preliminary data sheet
Rev. 00.01 — 5 October 2007
43 of 67
NXP Semiconductors
LPC2460
Fast communication chip
7.25.3
Brownout detection
The LPC2460 includes 2-stage monitoring of the voltage on the V
DD(3V3)
pins. If this
voltage falls below 2.95 V, the BOD asserts an interrupt signal to the Vectored Interrupt
Controller. This signal can be enabled for interrupt in the Interrupt Enable Register in the
VIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading a
dedicated status register.
The second stage of low-voltage detection asserts a BOD Reset and generates a Reset (if
this reset source is enabled in software) to inactivate the LPC2460 when the voltage on
the V
DD(3V3)
pins falls below 2.65 V. The BOD circuit maintains this reset down below 1 V,
at which point the power-on reset circuitry maintains the overall Reset.
Both the 2.95 V and 2.65 V thresholds include some hysteresis. In normal operation, this
hysteresis allows the 2.95 V detection to reliably interrupt, or a regularly-executed event
loop to sense the condition.
7.25.4
AHB bus
The LPC2460 implements two AHB buses in order to allow the Ethernet block to operate
without interference caused by other system activity. The primary AHB, referred to as
AHB1, includes the Vectored Interrupt Controller, GPDMA controller, USB interface, and
16 kB SRAM.
The second AHB, referred to as AHB2, includes only the Ethernet block and an
associated 16 kB SRAM. In addition, a bus bridge is provided that allows the secondary
AHB to be a bus master on AHB1, allowing expansion of Ethernet buffer space into
off-chip memory or unused space in memory residing on AHB1.
In summary, bus masters with access to AHB1 are the ARM7 itself, the USB block, the
GPDMA function, and the Ethernet block (via the bus bridge from AHB2). Bus masters
with access to AHB2 are the ARM7 and the Ethernet block.
7.25.5
External interrupt inputs
The LPC2460 includes up to 68 edge sensitive interrupt inputs combined with up to four
level sensitive external interrupt inputs as selectable pin functions. The external interrupt
inputs can optionally be used to wake up the processor from Power-down mode.
7.25.6
Memory mapping control
The memory mapping control alters the mapping of the interrupt vectors that appear at the
beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the Boot
ROM, the SRAM, or external memory. This allows code running in different memory
spaces to have control of the interrupts.
7.26 Emulation and debugging
The LPC2460 support emulation and debugging via a JTAG serial port. A trace port allows
tracing program execution. Debugging and trace functions are multiplexed only with
GPIOs on P2[0] to P2[9]. This means that all communication, timer, and interface
peripherals residing on other pins are available during the development and debugging
phase as they are when the application is run in the embedded system itself.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2880 | 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface |
| LPC2880FET180 | 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface |
| LPC2888 | 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface |
| LPC2888FET180 | 16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface |
| LPC2917 | ARM9 microcontroller with CAN and LIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2460_08 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit micro; Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface |
| LPC2460FBD208 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit microcontroller; Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface |
| LPC2460FBD208,551 | 功能描述:ARM微控制器 - MCU ARM7 USBHOST/ENET ROMLESS RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2460FBD208-S | 制造商:NXP Semiconductors 功能描述:MCU 16-Bit/32-Bit LPC2000 ARM7TDMI-S RISC ROMLess 3.3V 208-Pin LQFP Tray |
| LPC2460FET208 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit microcontroller; Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface |
發布緊急采購，3分鐘左右您將得到回復。