- 您現在的位置：買賣IC網 > PDF目錄385399 > HT47C20 (Holtek Semiconductor Inc.) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | HT47C20 |
| 廠商： | Holtek Semiconductor Inc. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 15/56頁 |
| 文件大小： | 352K |
| 代理商： | HT47C20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
HT47C20
15
January 18, 2000
External interrupt is triggered by a high to low
transition of INT and the related interrupt re-
quest flag (EIF; bit 4 of INTC0) will be set.
When the interrupt is enabled, and the stack is
not full and the external interrupt is active, a
subroutine call to location 04H will occur. The
interrupt request flag (EIF) and EMI bits will
be cleared to disable other interrupts.
The internal timer/event counter interrupt is
initialized by setting the timer/event counter
interrupt request flag (TF; bit 4 of INTC1),
caused by a timer A or timer B overflow. When
the interrupt is enabled, and the stack is not
full and the TF bit is set, a subroutine call to lo-
cation 10H will occur. The related interrupt re-
quest flag (TF) will be reset and the EMI bit
cleared to disable further interrupts.
The time base interrupt is initialized by setting
the time base interrupt request flag (TBF; bit 5
of INTC0), caused by a regular time base sig-
nal. When the interrupt is enabled, and the
stack is not full and the TBF bit is set, a subrou-
tine call to location 08H will occur. The related
interrupt request flag (TBF) will be reset and
the EMI bit cleared to disable further inter-
rupts.
The real time clock interrupt is initialized by
setting the real time clock interrupt request
flag (RTF; bit 6 of INTC0), caused by a regular
real time clock signal. When the interrupt is en-
abled, and the stack is not full and the RTF bit
is set, a subroutine call to location 0CH will oc-
cur. The related interrupt request flag (RTF)
will be reset and the EMI bit cleared to disable
further interrupts.
During the execution of an interrupt subrou-
tine, other interrupt acknowledgments are held
until the RETI instruction is executed or the
EMI bit and the related interrupt control bit
are set to 1 (if the stack is not full). To return
from the interrupt subroutine, RET or RETI in-
struction may be invoked. RETI will set the
EMI bit to enable an interrupt service, but RET
does not.
Interrupts occurring in the interval between
the rising edges of two consecutive T2 pulses,
will be serviced on the latter of the two T2
pulses, if the corresponding interrupts are en-
abled. In the case of simultaneous requests the
following table shows the priority that is ap-
plied. These can be masked by resetting the
EMI bit.
No.
Interrupt Source Priority Vector
a
External interrupt
1
04H
b
Time base interrupt
2
08H
c
Real time clock
interrupt
3
0CH
d
Timer/event counter
interrupt
4
10H
The external interrupt request flag (EIF), real
timeclockinterruptrequestflag(RTF),timebase
interrupt request flag (TBF), enable external in-
terrupt bit (EEI), enable real time clock interrupt
bit (ERTI), enable time base interrupt bit (ETBI),
and enable master interrupt bit (EMI) constitute
an interrupt control register 0 (INTC0) which is
located at 0BH in the data memory. The
timer/event counter interrupt request flag (TF),
enable timer/event counter interrupt bit (ETI) on
the other hand, constitute an interrupt control
register 1 (INTC1) which is located at 1EH in the
data memory. EMI, EEI, ETI, ETBI, and ERTI
are used to control the enabling/disabling of in-
terrupts. These bits prevent the requested inter-
rupt being serviced. Once the interrupt request
flags (RTF, TBF, TF, EIF) are set, they remain in
the INTC1 or INTC0 respectively until the inter-
rupts are serviced or cleared by a software in-
struction.
It is recommended that a program does not use
the
CALL subroutine
subroutine. Because interrupts often occur in
an unpredictable manner or need to be serviced
immediately in some applications, if only one
stack is left, and enabling the interrupt is not
well controlled, once the CALLsubroutine op-
erates in the interrupt subroutine will damage
the original control sequence.
within the interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| HT47R20 | 8 位R-F 型OTP 單片機 |
| HT48C05 | Cost-Effective I/O Type 8-Bit MCU |
| HT48C06 | Cost-Effective I/O Type 8-Bit MCU |
| HT48C10-1 | 8-Bit High Performance RISC-like Microcontroller Suitable for Multiple I/O Application(高性能、指令類似RISC的8位微控制器，用于多I/O接口設備) |
| HT48C50-1 | 8-Bit High Performance RISC-like Microcontroller Suitable for Multiple I/O Application(高性能、指令類似RISC的8位微控制器，用于多I/O接口設備) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT47C20_02 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit R-F Type Mask MCU |
| HT47C20-1 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:R-F Type 8-Bit MCU |
| HT47C20-1_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:R-F Type 8-Bit MCU |
| HT47C20L | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Microcontroller |
| HT47C20L_05 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:R-F Type Low Voltage 8-Bit Mask MCU |
發布緊急采購，3分鐘左右您將得到回復。