- 您現在的位置：買賣IC網 > PDF目錄382970 > FT2232C (Electronic Theatre Controls, Inc.) FT2232C Dual USB UART / FIFO I.C. PDF資料下載
參數資料
| 型號： | FT2232C |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | FT2232C Dual USB UART / FIFO I.C. |
| 中文描述： | FT2232C雙USB的UART / FIFO的集成電路 |
| 文件頁數： | 7/51頁 |
| 文件大?。?/td> | 907K |
| 代理商： | FT2232C |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
DS2232C Version 1.4
Future Technology Devices International Ltd. 2005 Page 7 of 54
FT2232C Dual USB UART / FIFO I.C.
6MHz Oscillator
The 6MHz Oscillator cell generates a 6MHz
reference clock input to the x8 Clock multiplier from
an external 6MHz crystal or ceramic resonator.
x8 Clock Multiplier
The x8 Clock Multiplier takes the 6MHz input
from the Oscillator cell and generates a 48MHz
reference clock for the USB DPPL and the Baud
Rate Generator blocks.
Serial Interface Engine (SIE)
The Serial Interface Engine (SIE) block performs
the Parallel to Serial and Serial to Parallel
conversion of the USB data. In accordance to the
USB 2.0 specification, it performs bit stuffing / un-
stuffing and CRC5 / CRC16 generation / checking
on the USB data stream.
USB Protocol Engine
The USB Protocol Engine manages the data
stream from the device USB control endpoint. It
handles the low level USB protocol (Chapter 9)
requests generated by the USB host controller
and the commands for controlling the functional
parameters of the UART / FIFO controller blocks.
Dual Port TX Buffers (128 bytes)
Data from the USB data out endpoint is stored
in the Dual Port TX buffer and removed from the
buffer to the transmit register under control of the
UART FIFO controller.
Dual Port RX Buffers (384 bytes)
Data from the UART / FIFO controller receive
register is stored in the Dual Port RX buffer prior
to being removed by the SIE on a USB request for
data from the device data in endpoint.
Multi-Purpose UART / FIFO Controllers
The Multi-purpose UART / FIFO controllers handle
the transfer of data between the Dual Port RX
and TX buffers and the UART / FIFO transmit
and receive registers.
When configured as a
UART it performs asynchronous 7 / 8 bit Parallel
to Serial and Serial to Parallel conversion of the
data on the RS232 (RS422 and RS485) interface.
Control signals supported by UART mode include
RTS, CTS, DSR , DTR, DCD and RI. There
are also transmitter enable control signal pins
(TXDEN) provided to assist with interfacing to
RS485 transceivers. RTS/CTS, DSR/DTR and
Xon/Xoff handshaking options are also supported.
Handshaking, where required, is handled in
hardware to ensure fast response times. The
UART’s also supports the RS232 BREAK setting
and detection conditions.
Baud Rate Generator
The Baud Rate Generator provides a x16 clock
input to the UART’s from the 48MHz reference
clock and consists of a 14 bit prescaler and 3
register bits which provide fine tuning of the baud
rate (used to divide by a number plus a fraction).
This determines the Baud Rate of the UART which
is programmable from 183 baud to 3 million baud.
RESET Generator
The Reset Generator Cell provides a reliable
power-on reset to the device internal circuitry
on power up. An additional RESET# input and
RSTOUT# output are provided to allow other
devices to reset the FT2232C, or the FT2232C
to reset other devices respectively. During reset,
RSTOUT# is driven low, otherwise it drives out
at the 3.3V provided by the onboard regulator.
RSTOUT# can be used to control the 1.5K
pull-up on USBDP directly where delayed USB
enumeration is required. It can also be used to
reset other devices. RSTOUT# will stay high-
impedance for approximately 5ms after VCC
has risen above 3.5V AND the device oscillator is
running AND RESET# is high. RESET# should
be tied to VCC unless it is a requirement to reset
the device from external logic or an external reset
generator I.C.
相關PDF資料 |
PDF描述 |
|---|---|
| FT245BL | FT245BL USB FIFO ( USB - Parallel ) I.C. |
| FT245BM | FT245BM USB FIFO ( USB - Parallel ) I.C. |
| FT245BQ | FT245BQ USB FIFO ( USB - Parallel ) I.C. |
| FT6116 | 2K X 8 CMOS SRAM |
| FT8U100AX | FT8U100AX USB Compound Hub Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232C_04 | 制造商:FTDI 制造商全稱:FTDI 功能描述:Dual USB UART / FIFO I.C. |
| FT2232D | 制造商:Future Technology Devices International 功能描述:UART 2-CH 3.3V/5V 48-Pin LQFP 制造商:Future Technology Devices International 功能描述:UART 2-CH 3.3V/5V 48-Pin LQFP Bulk 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Full Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - LQFP-48 |
| FT2232D/TR | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB-UART/FIFO SMD 2232 LQFP48 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB-UART/FIFO, SMD, 2232, LQFP48 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB-UART/FIFO, SMD, 2232, LQFP48; USB Type:FIFO; USB Version:2.0; Supply Voltage Min:3V; Supply Voltage Max:5.25V; Digital IC Case Style:LQFP; No. of Pins:48; Data Rate:12Mbps; No. of Ports:2; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| FT2232D-REEL | 功能描述:USB 接口集成電路 USB to Dual UART/ FIFO/SPI/JTAG/I2C RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT2232D-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:DUAL USB TO SERIAL UART/FIFO IC |
發布緊急采購，3分鐘左右您將得到回復。