- 您現在的位置：買賣IC網 > PDF目錄381841 > FDC37B80X (STANDARD MICROSYSTEMS CORP) PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up PDF資料下載
參數資料
| 型號： | FDC37B80X |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 98/194頁 |
| 文件大?。?/td> | 802K |
| 代理商： | FDC37B80X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁當前第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
98
Command/Data
ECP Mode supports two advanced features to
improve the effectiveness of the protocol for
some
applications.
implemented by allowing the transfer of normal
8 bit data or 8 bit commands.
The
features
are
When in the forward direction, normal data is
transferred when HostAck is high and an 8 bit
command is transferred when HostAck is low.
The most significant bit of the command
indicates whether it is a run-length count (for
compression) or a channel address.
When in the reverse direction, normal data is
transferred when PeriphAck is high and an 8 bit
command is transferred when PeriphAck is low.
The most significant bit of the command is
always zero. Reverse channel addresses are
seldom used and may not be supported in
hardware.
Table 40 -
Forward Channel Commands (HostAck Low)
Reverse Channel Commands (PeripAck Low)
D7
0
Run-Length Count (0-127)
(mode 0011 0X00 only)
1
Channel Address (0-127)
D[6:0]
Data Compression
The ECP port supports run length encoded
(RLE) decompression in hardware and can
transfer compressed data to a peripheral. Run
length encoded (RLE) compression in hardware
is not supported. To transfer compressed data
in ECP mode, the compression count is written
to the ecpAFifo and the data byte is written to
the ecpDFifo.
Compression is accomplished by counting
identical bytes and transmitting an RLE byte
that indicates how many times the next byte is
to be repeated. Decompression simply
intercepts the RLE byte and repeats the
following byte the specified number of times.
When a run-length count is received from a
peripheral, the subsequent data byte is
replicated the specified number of times. A
run-length count of zero specifies that only one
byte of data is represented by the next data
byte, whereas a run-length count of 127
indicates that the next byte should be expanded
to 128 bytes. To prevent data expansion,
however, run-length counts of zero should be
avoided.
Pin Definition
The drivers for nStrobe, nAutoFd, nInit and
nSelectIn are open-collector in mode 000 and
are push-pull in all other modes.
ISA Connections
The interface can never stall causing the host to
hang. The width of data transfers is strictly
controlled on an I/O address basis per this
specification. All FIFO-DMA transfers are byte
wide, byte aligned and end on a byte boundary.
(The PWord value can be obtained by reading
Configuration Register A, cnfgA, described in
the next section). Single byte wide transfers
are always possible with standard or PS/2 mode
using program control of the control signals.
Interrupts
The interrupts are enabled by serviceIntr in the
ecr register.
serviceIntr = 1 Disables the DMA and all of the
service interrupts.
serviceIntr = 0 Enables the selected interrupt
condition. If the interrupting
condition is valid, then the
interrupt
immediately when this bit is
changed from a 1 to a 0. This
can occur during Programmed
I/O if the number of bytes
removed or added from/to the
is
generated
相關PDF資料 |
PDF描述 |
|---|---|
| FDC37C665IR | 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support |
| FDC37C665GT | High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
| FDC37C666GT | High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
| FDC37C67X | ENHANCED SUPER I/O CONTROLLER WITH FAST IR |
| FDC37C957FR | ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FDC37C651 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Floppy Disk Controller |
| FDC37C651QFP | 制造商:SMC 功能描述: 制造商:SMSC 功能描述: 制造商:SMC Corporation of America 功能描述:FDC37C651QFP |
| FDC37C652 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Floppy Disk Controller |
| FDC37C652QFP | 制造商:SMSC 功能描述: |
| FDC37C653QFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。