參數資料
型號： FDC37B80X
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 外設及接口
英文描述： PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up
中文描述： MULTIFUNCTION PERIPHERAL, PQFP100
封裝： QFP-100
文件頁數： 100/194頁
文件大?。?/td> 802K
代理商： FDC37B80X
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁當前第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
100
a minimum of 350nsec. (Note: The only way to
properly terminate DMA transfers is with a TC.)
DMA may be disabled in the middle of a transfer
by first disabling the host DMA controller. Then
setting serviceIntr to 1, followed by setting
dmaEn to 0, and waiting for the FIFO to become
empty
or
full.
Restarting
accomplished by enabling DMA in the host,
setting dmaEn to 1, followed by setting
serviceIntr to 0.
the
DMA
is
DMA Mode - Transfers from the FIFO to the
Host
(Note: In the reverse mode, the peripheral may
not continue to fill the FIFO if it runs out of data
to transfer, even if the chip continues to request
more data from the peripheral.)
The ECP activates the PDRQ pin whenever
there is data in the FIFO. The DMA controller
must respond to the request by reading data
from the FIFO. The ECP will deactivate the
PDRQ pin when the FIFO becomes empty or
when the TC becomes true (qualified by
nPDACK), indicating that no more data is
required. PDRQ goes inactive after nPDACK
goes active for the last byte of a data transfer
(or on the active edge of nIOR, on the last byte,
if no edge is present on nPDACK). If PDRQ
goes inactive due to the FIFO going empty, then
PDRQ is active again as soon as there is one
byte in the FIFO. If PDRQ goes inactive due to
the TC, then PDRQ is active again when there is
one byte in the FIFO, and serviceIntr has been
re-enabled. (Note: A data underrun may occur if
PDRQ is not removed in time to prevent an
unwanted cycle).
Programmed I/O Mode or Non-DMA Mode
The ECP or parallel port FIFOs may also be
operated using interrupt driven programmed I/O.
Software can determine the writeIntrThreshold,
readIntrThreshold, and FIFO depth by accessing
the FIFO in Test Mode.
Programmed I/O transfers are to the ecpDFifo
at 400H and ecpAFifo at 000H or from the
ecpDFifo located at 400H, or to/from the tFifo at
400H. To use the programmed I/O transfers,
the host first sets up the direction and state, sets
dmaEn to 0 and serviceIntr to 0.
The ECP requests programmed I/O transfers
from the host by activating the PINTR pin. The
programmed I/O will empty or fill the FIFO using
the appropriate direction and mode.
Note: A threshold of 16 is equivalent to a
threshold of 15. These two cases are treated
the same.
Programmed I/O - Transfers from the FIFO to
the Host
In the reverse direction an interrupt occurs when
serviceIntr is 0 and readIntrThreshold bytes
are available in the FIFO. If at this time the
FIFO is full it can be emptied completely in a
single burst, otherwise readIntrThreshold bytes
may be read from the FIFO in a single burst.
readIntrThreshold =(16-<threshold>) data bytes
in FIFO
相關PDF資料
PDF描述
FDC37C665IR 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C666GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
FDC37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
相關代理商/技術參數
參數描述
FDC37C651 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Floppy Disk Controller
FDC37C651QFP 制造商:SMC 功能描述: 制造商:SMSC 功能描述: 制造商:SMC Corporation of America 功能描述:FDC37C651QFP
FDC37C652 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Floppy Disk Controller
FDC37C652QFP 制造商:SMSC 功能描述:
FDC37C653QFP 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*