參數資料
型號: CS8420-CSZ
廠商: Cirrus Logic Inc
文件頁數: 25/94頁
文件大小: 0K
描述: IC SAMPLE RATE CONVERTER 28SOIC
標準包裝: 27
類型: 采樣率轉換器
應用: CD-R,DAT,DVD,MD,VTR
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 28-SOIC
包裝: 管件
產品目錄頁面: 759 (CN2011-ZH PDF)
配用: 598-1782-ND - EVALUATION BOARD FOR CS8420
其它名稱: 598-1125-5
DS245F4
31
CS8420
9.2
IC Mode
In IC mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL, with
the clock to data relationship as shown in Figure 23. There is no CS pin. Each individual CS8420 is given a
unique address. Pins AD[1:0] form the two least significant bits of the chip address and should be connected
to VD+ or DGND as desired. The EMPH pin is used to set the AD2 bit, by connecting a resistor from the
EMPH pin to VD+ or to DGND. The state of the pin is sensed while the CS8420 is being reset. The upper
four bits of the 7-bit address field are fixed at 0010b. To communicate with a CS8420, the chip address field,
which is the first byte sent to the CS8420, should match 0010b followed by the settings of the EMPH, AD1,
and AD0. The eighth bit of the address is the R/W bit. If the operation is a write, the next byte is the Memory
Address Pointer (MAP) which selects the register to be read or written. If the operation is a read, the con-
tents of the register pointed to by the MAP will be output. Setting the auto-increment bit in MAP allows suc-
cessive reads or writes of consecutive registers. Each byte is separated by an acknowledge bit. The ACK
bit is output from the CS8420 after each input byte is read and is input to the CS8420 from the microcon-
troller after each transmitted byte.
9.3
Interrupts
The CS8420 has a comprehensive interrupt capability. The INT output pin is intended to drive the interrupt
input pin on the host microcontroller. The INT pin may be set to be active-low, active-high, or active-low with
no active pull-up transistor. This last mode is used for active-low, wired-OR hook-ups, with multiple periph-
erals connected to the microcontroller interrupt input pin.
Many conditions can cause an interrupt, as listed in the interrupt status register descriptions. Each source
may be masked via mask registers. In addition, each source may be set to rising-edge, falling-edge, or level-
sensitive. Combined with the option of level-sensitive or edge-sensitive modes within the microcontroller,
many different set-ups are possible, depending on the needs of the equipment designer.
SDA
SCL
0010
AD2-0
R/W
Start
ACK
DATA7-0
ACK
DATA7-0
ACK
Stop
Note 2
Note 1
Note 3
Figure 23. Control Port Timing in
IC Mode
1.
AD2 is derived from a resistor attached to the EMPH pin
AD1, and AD0 are determined by the state of the corresponding pins.
2.
If operation is a write, this byte contains the Memory Address Pointer, MAP.
3.
If operation is a read, the last bit of the read should be NACK (high).
Notes:
相關PDF資料
PDF描述
15280-18PG-321 CONN JACK 18POS CABLE PIN
CS496112-CQZ IC DSP 32BIT 8CH SER I/O 144LQFP
CS181022-CQZ IC COBRANET CS181022 144LQFP
AD1896AYRSZ IC CONV SAMPLE RATE ASYNC 28SSOP
CS6422-CSZ IC SPEAKERPHONE ENHANCED 20SOIC
相關代理商/技術參數
參數描述
CS8420-CSZ/D1 制造商:Cirrus Logic 功能描述:
CS8420-CSZR 功能描述:音頻 DSP IC Digital Audio Sample Rate Convertr RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
CS8420-CSZR/D1 制造商:Cirrus Logic 功能描述:
CS8420-DS 功能描述:音頻 DSP Digital Audio Sample Rate Converter RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
CS8420-DSR 功能描述:音頻 DSP IC Digital Audio Sample Rate Convertr RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube