- 您現在的位置：買賣IC網 > PDF目錄366869 > COP942CT PDF資料下載
參數資料
| 型號： | COP942CT |
| 文件頁數： | 8/36頁 |
| 文件大?。?/td> | 479K |
| 代理商： | COP942CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
DC Electrical Characteristics COP84x
(Continued)
40C
≤
T
A
≤
+85C unless otherwise specified
Parameter
Maximum Input Current
without Latchup (Note 12)
RAM Retention Voltage, Vr
Input Capacitance
Load Capacitance on D2
Condition
Min
Typ
Max
±
100
Units
mA
500 ns Rise and Fall Time (min)
2.0
V
pF
pF
7
1000
Note 9:
Rate of voltage change must be
<
10V/ms.
Note 10:
Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 11:
The HALT mode will stop CKI from oscillating in the RC and crystal configurations. HALT test conditions: L, and G0..G5 ports configured as outputs and
set high. The D port set to zero. All inputs tied to V
CC
. The comparator and the Brown Out circuits are disabled.
Note 12:
Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than V
and the pins will have sink current
to V
when biased at voltages greater than V
(the pins do not have source current when biased at a voltage below V
CC
). The effective resistance to V
CC
is 750
(typical). These two pins will not latch up. The voltage at the pins must be limited to
<
14V.
Note 13:
The Resistor values are for R/C only.
AC Electrical Characteristics COP84x
40C
≤
T
A
≤
+85C unless otherwise specified.
Parameter
Instruction Cycle Time (t
C
)
Crystal/Resonator
Condition
Min
Typ
Max
Units
4.5V
≤
V
CC
<
6.0V
2.5V
≤
V
CC
<
4.5V
4.5V
<
V
CC
<
6.0V
2.5V
≤
V
CC
<
4.5V
1
DC
DC
DC
DC
μs
μs
μs
μs
μs
MHz
MHz
%
ns
ns
2.5
2
5
50
R/C Oscillator
V
CC
Rise Time when Using Brown Out
Frequency at Brown Out Reset
CKI Frequency for Modulator Output
CKI Clock Duty Cycle (Note 14)
Rise Time (Note 14)
Fall Time (Note 14)
Inputs
t
Setup
4
4
60
12
8
fr = Max
fr = 10 MHz ext. clock
fr = 10 MHz ext. clock
40
4.5V
≤
V
CC
<
6.0V
2.5V
≤
V
CC
<
4.5V
4.5V
≤
V
CC
<
6.0V
2.5V
≤
V
CC
<
4.5V
R
L
= 2.2k, C
L
= 100 pF
200
500
60
150
ns
ns
ns
ns
t
Hold
Output Propagation Delay
t
PD1
, t
PD0
SO, SK
4.5V
≤
V
CC
<
6.0V
2.5V
≤
V
CC
<
4.5V
4.5V
≤
V
CC
<
6.0V
2.5V
≤
V
CC
<
4.5V
0.7
1.75
1
5
μs
μs
μs
μs
t
C
t
C
t
C
t
C
t
C
ns
ns
All Others
Input Pulse Width
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer input low time
MICROWIRE Setup Time (t
μWS
)
MICROWIRE Hold Time (t
μWH
)
MICROWIRE Output
Propagation Delay (t
μPD
)
Reset Pulse Width
1
1
1
1
1
20
56
220
ns
μs
1.0
Note 14:
Parameter sampled but not 100% tested.
C
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| COPC912 | |
| COPCH912 | |
| COPCH912C | 8-BIT MICROCONTROLLER |
| COP912C | 8-Bit Microcontroller(8位微控制器) |
| CP08-127-06L | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP942C-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP942C-XXX/WM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP943C-XXX/N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| COP980C | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Microcontrollers |
| COP980CH-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:COP880C Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。