- 您現在的位置：買賣IC網 > PDF目錄366869 > COP942CT PDF資料下載
參數資料
| 型號： | COP942CT |
| 文件頁數： | 18/36頁 |
| 文件大小： | 479K |
| 代理商： | COP942CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
WATCHDOG
(Continued)
Modulator/Timer
The MODULATOR/TIMER contains an 8-bit counter and an
8-bit autoreload register (MODRL address 0CF Hex). The
Modulator/Timer has two modes of operation, selected by
the control bit MC3. The Modulator/Timer Control bits MC1,
MC2 and MC3 reside in CNTRL2 Register.
MODE 1: MODULATOR
The Modulator is used to generate high frequency pulses on
the modulator output pin (L7). The L7 pin should be config-
ured as an output. The number of pulses is determined by
the 8-bit down counter. Under software control the modulator
input clock can be either CKI or t
C
. The t
C
clock is derived by
dividing down the oscillator clock by a factor of 10. Three
control bits (MC1, MC2, and MC3) are used for the
Modulator/Timer output control. When MC2 = 1 and MC3 =
1, CKI is used as the modulator input clock. When MC2 = 0,
and MC3 = 1, t
is used as the modulator input clock. The
user loads the counter with the desired number of counts
(256 max) and sets MC1 to start the counter. The modulator
autoreload register is loaded with n-1 to get n pulses. CKI or
t
pulses are routed to the modulator output (L7) until the
counter underflows (Figure 11) Upon underflow the hard-
ware resets MC1 and stops the counter. The L7 pin goes low
and stays low until the counter is restarted by the user pro-
gram. The user program has the responsibility to time-out
the low time. Unless the number of counts is changed, the
user program does not have to load the counter each time
the counter is started. The counter can simply be started by
setting the MC1 bit. Setting MC1 by software will load the
counter with the value of the autoreload register. The soft-
ware can reset MC1 to stop the counter.
MODE 2: PWM TIMER
The counter can also be used as a PWM Timer. In this mode,
an 8-bit register is used to serve as an autoreload register
(MODRL).
1.
50% Duty Cycle:
When MC1 is 1 and MC2, MC3 are 0, a 50% duty cycle
free running signal is generated on the L7 output pin
(Figure 12) The L7 pin must be configured as an output
pin. In this mode the 8-bit counter is clocked by t
C
. Set-
ting the MC1 control bit by software loads the counter
with the value of the autoreload register and starts the
counter. The counter underflow toggles the (L7) output
pin. The 50% duty cycle signal will be continuously gen-
erated until MC1 is reset by the user program.
DS012851-21
FIGURE 10. WATCHDOG Timer Block Diagram
C
www.national.com
18
相關PDF資料 |
PDF描述 |
|---|---|
| COPC912 | |
| COPCH912 | |
| COPCH912C | 8-BIT MICROCONTROLLER |
| COP912C | 8-Bit Microcontroller(8位微控制器) |
| CP08-127-06L | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP942C-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP942C-XXX/WM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP943C-XXX/N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| COP980C | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Microcontrollers |
| COP980CH-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:COP880C Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。