- 您現在的位置：買賣IC網 > PDF目錄366869 > COP942CT PDF資料下載
參數資料
| 型號： | COP942CT |
| 文件頁數： | 13/36頁 |
| 文件大?。?/td> | 479K |
| 代理商： | COP942CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Reset
(Continued)
BROWN OUT RESET
The on-board Brown Out detection circuit resets the device
when the operating voltage (V
) is lower than the Brown
Out voltage. The device is held in reset when V
stays be-
low the Brown Out voltage. The device will remain in RESET
as long as V
is below the Brown Out Voltage. The device
will resume execution if V
rises above the Brown Out Volt-
age. If a two pin crystal/resonator clock option is selected,
the Brown Out reset will trigger a 256 tc delay. This delay al-
lows the oscillator to stabilize before the device exits the re-
set state. The delay is not used if the clock option is either
R/C or external clock. The contents of data registers and
RAM are unknown following a Brown Out reset. The external
reset takes priority over Brown Out Reset and will deactivate
the 256 tc cycles delay if in progress. The Brown Out reset
takes priority over the WATCHDOG reset.
The following actions occur as a result of Brown Out reset:
Port L:
Port G:
Port D
PC:
RAM Contents:
B, X, SP
PSW, CNTRL1, CNTRL2
and WDREG Registers:
Multi-Input Wake-up
Registers (WKEDG,
WKEN):
(WKPND):
Data and Configuration
Registers for L and G:
WATCHDOG Timer:
TRI-STATE
TRI-STATE
HIGH
CLEARED
RANDOM
UNKNOWN
CLEARED
CLEARED
UNKNOWN
CLEARED
Prescaler/Counter each
loaded with FF
Unknown data after
coming
out of the HALT (through
Brown Out Reset) with any
Clock option
Timer T1 and
Accumulator:
Note:
The Development system will detect the BROWN OUT RESET exter-
nally and will force the RESET pin low. The Development System does
not emulate the 256 tc delay.
Brown Out Detection
An on-board detection circuit monitors the operating voltage
(V
) and compares it with the minimum operating voltage
specified. The Brown Out circuit is designed to reset the de-
vice if the operating voltage is below the Brown Out voltage
(between 1.8V–4.2V at 40C to +85C). The Minimum oper-
ating voltage for the device is 2.5V with Brown Out disabled,
but with Brown Out enabled the device is guaranteed to op-
erate properly down to minimum Brown Out voltage (Max
frequency 4 MHz). For temperature range of 0C–70C the
Brown Out voltage is expected to be between 1.9V and 3.9V.
The circuit can be enabled or disabled by Brown Out mask
option. If the device is intended to operate at lower V
(lower than Brown Out voltage VBO max), the Brown Out cir-
cuit should be disabled by the mask option.
The Brown Out circuit may be used as a power-up reset pro-
vided the power supply rise time is slower than 50 μs
(0V–6.0V). Brown Out should not be used in frequencies
over 4 MHz.
Note:
Brown Out Circuit is active in HALT mode (with the Brown Out mask
option selected).
Oscillator Circuits
EXTERNAL OSCILLATOR
By selecting the external oscillator option, the CKI pin can be
driven by an external clock signal provided it meets the
specified duty cycle, rise and fall times, and input levels. The
G7/CKO is available as a general purpose input G7 and/or
Halt control.
CRYSTAL OSCILLATOR
By selecting the crystal oscillator option, the G7/CKO pin is
connected as a clock output, CKI and G7/CKO can be con-
nected to make a crystal controlled oscillator. Table 1 shows
the clock frequency for different component values. See Fig-
ure 4 for the connections.
R/C OSCILLATOR
By selecting the R/C oscillator option, connecting a resistor
from the CKI pin to V
makes a R/C oscillator. The capaci-
tor is on-chip. The G7/CKO pin is available as a general pur-
pose input G7 and/or Halt control. Adding an external ca-
pacitor will jeopardize the clock frequency tolerance and
increase EMI emissions.
Table 2 shows the clock frequency for the different resistor
values. The capacitor is on-chip. See Figure 4 for the
connections.
DS012851-15
FIGURE 4. Clock Oscillator Configurations
C
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| COPC912 | |
| COPCH912 | |
| COPCH912C | 8-BIT MICROCONTROLLER |
| COP912C | 8-Bit Microcontroller(8位微控制器) |
| CP08-127-06L | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP942C-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP942C-XXX/WM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP943C-XXX/N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| COP980C | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Microcontrollers |
| COP980CH-XXX/N | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:COP880C Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。