- 您現在的位置：買賣IC網 > PDF目錄374039 > ADUC836BS (ANALOG DEVICES INC) MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU PDF資料下載
參數資料
| 型號： | ADUC836BS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| 中文描述： | 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | 14 X 14 MM, MO-022-AC-1, MQFP-52 |
| 文件頁數： | 51/80頁 |
| 文件大?。?/td> | 5913K |
| 代理商： | ADUC836BS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
ADuC836
–51–
Notice also that direct access to the SCLOCK and SDATA/MOSI
pins is afforded through the SFR interface in I
2
C master mode.
Therefore, if you are not using the SPI or I
2
C functions, you can
use these two pins to provide additional high current digital outputs.
HARDWARE SPI
(MASTER/SLAVE)
Q3
SCHMITT
TRIGGER
Q1
Q2 (OFF)
DV
DD
SCLOCK
PIN
Q4 (OFF)
SPE = 1 (SPI ENABLE)
Figure 42. SCLOCK Pin I/O Functional Equivalent
in SPI Mode
MCO
I
2
CM
SFR
BITS
50ns GLITCH
REJECTION FILTER
HARDWARE I
2
C
(SLAVE ONLY)
Q3
Q4
SCLOCK
PIN
Q2
Q1
(OFF)
DV
DD
SPE = 0 (I
2
C ENABLE)
Figure 43. SCLOCK Pin I/O Functional Equivalent
in I
2
C Mode
HARDWARE SPI
(MASTER/SLAVE)
Q3
Q1
Q2 (OFF)
DV
DD
SDATA/
MOSI
PIN
Q4 (OFF)
SPE = 1 (SPI ENABLE)
Figure 44. SDATA/MOSI Pin I/O Functional Equivalent
in SPI Mode
Q3
Q4
Q2
Q1
(OFF)
DV
DD
MDI
MDO
MDE
I2CM
HARDWARE I
2
C
(SLAVE ONLY)
50ns GLITCH
REJECTION FILTER
SDATA/
MOSI
PIN
SFR
BITS
SPE = 0 (I
2
C ENABLE)
Figure 45. SDATA/MOSI Pin I/O Functional Equivalent
in I
2
C Mode
As shown in Figure 46, the MISO pin in SPI master/slave opera-
tion offers the exact same pull-up and pull-down configuration as
the MOSI pin in SPI slave/master operation.
The
SS
pin has a weak internal pull-up permanently enabled to
prevent the
SS
input from floating. This pull-up can be easily
overdriven by an external device to drive the
SS
pin low.
HARDWARE SPI
(MASTER/SLAVE)
MISO
PIN
DV
DD
Figure 46. MISO Pin I/O Functional Equivalent
HARDWARE SPI
(MASTER/SLAVE)
SS
PIN
DV
DD
Figure 47.
SS
Pin I/O Functional Equivalent
Read-Modify-Write Instructions
Some 8051 instructions that read a port, read the latch and
others read the pin. The instructions that read the latch rather
than the pins are the ones that read a value, possibly change it,
and then rewrite it to the latch. These are called “read-modify-
write” instructions. which are listed below. When the destination
operand is a port or a port bit, these instructions read the latch
rather than the pin.
ANL (Logical AND, e.g., ANL P1, A)
ORL (Logical OR, e.g., ORL P2, A)
XRL (Logical EX-OR, e.g., XRL P3, A)
JBC (Jump If Bit = 1 and Clear Bit,
e.g., JBC P1.1, LABEL
CPL (Complement Bit, e.g., CPL P3.0)
INC (Increment, e.g., INC P2)
DEC (Decrement, e.g., DEC P2)
DJNZ (Decrement and Jump IFf Not Zero,
e.g.,DJNZ P3, LABEL)
MOV PX.Y, C
*
(Move Carry to Bit Y of Port X)
CLR PX.Y
*
(Clear Bit Y of Port X)
SETB PX.Y
*
(Set Bit Y of Port X)
*
These instructions read the port byte (all eight bytes), modify the addressed bit
and then write the new byte back to the latch.
The reason that read-modify-write instructions are directed to
the latch rather than to the pin is to avoid a possible misinter-
pretation of the voltage level of a pin. For example, a port pin
might be used to drive the base of a transistor. When a 1 is written
to the bit, the transistor is turned on. If the CPU then reads the
same port bit at the pin rather than the latch, it will read the base
voltage of the transistor and interpret it as a Logic 0. Reading the
latch rather than the pin will return the correct value of 1.
REV. A
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC842BCP62-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC843BCP62-5 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC842BCP62-5 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC843BCP62-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC842BCP32-3 | MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC836BS | 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS)) |
| ADUC836BSZ | 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC841 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC841BCP32-5 | 制造商:Analog Devices 功能描述:MICROCONVERTER 1-CYCLE VERSION ADUC829 - Trays |
| ADUC841BCP62-3 | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 20MHZ 3.3V 56LFCSP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。