參數資料
型號： ADUC836BS
廠商： ANALOG DEVICES INC
元件分類： 微控制器/微處理器
英文描述： MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU
中文描述： 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52
封裝： 14 X 14 MM, MO-022-AC-1, MQFP-52
文件頁數： 30/80頁
文件大小： 5913K
代理商： ADUC836BS
ADuC836
–30–
Flash/EE Program Memory
The ADuC836 contains a 64 Kbyte array of Flash/EE program
memory. The lower 62 Kbytes of this program memory are avail-
able to the user, and can be used for program storage or indeed
as additional NV data memory.
The upper 2 Kbytes of this Flash/EE program memory array con-
tain permanently embedded firmware, allowing in-circuit serial
download, serial debug, and nonintrusive single pin emulation.
These 2 Kbytes of embedded firmware also contain a power-on
configuration routine that downloads factory calibrated coeffi-
cients to the various calibrated peripherals (ADC, temperature
sensor, current sources, band gap references, and so on).
This 2 Kbyte embedded firmware is hidden from user code.
Attempts to read this space will read 0s, i.e., the embedded firm-
ware appears as NOP instructions to user code.
In normal operating mode (power-up default), the 62 Kbytes of
user Flash/EE program memory appear as a single block. This
block is used to store the user code, as shown in Figure 17.
FFFFH
2 KBYTE
0000H
F800H
F7FFH
USER PROGRAM MEMORY
62 KBYTES OF FLASH/EE PROGRAM MEMORY IS
AVAILABLE TO THE USER. ALL OF THIS SPACE CAN
BE PROGRAMMED FROM THE PERMANENTLY
EMBEDDED DOWNLOAD/DEBUG KERNEL OR IN
PARALLEL PROGRAMMING MODE.
EMBEDDED DOWNLOAD/DEBUG KERNEL
PERMANENTLY EMBEDDED FIRMWARE ALLOWS CODE
TO BE DOWNLOADED TO ANY OF THE 62 KBYTES OF
ON-CHIP PROGRAM MEMORY. THE KERNEL PROGRAM
APPEARS AS ‘NOP’ INSTRUCTIONS TO USER CODE.
62 KBYTE
Figure 17 Flash/EE Program Memory Map in Normal Mode
In Normal mode, the 62 Kbytes of Flash/EE program memory
can be programmed by serial downloading or parallel processing:
(1) Serial Downloading (In-Circuit Programming)
The ADuC836 facilitates code download via the standard UART
serial port. The ADuC836 will enter Serial Download mode after
a reset or power cycle if the
PSEN
pin is pulled low through an
external 1 k
resistor. Once in serial download mode, the hidden
embedded download kernel will execute. This allows the user to
download code to the full 62 Kbytes of Flash/EE program memo-
ry while the device is in circuit in its target application hardware.
A PC serial download executable is provided as part of the
ADuC836 QuickStart development system. Application Note
uC004 fully describes the serial download protocol that is used
available at
www.analog.com/microconverter
.
(2) Parallel Programming
The Parallel Programming mode is fully compatible with con-
ventional third party Flash or EEPROM device programmers.
A block diagram of the external pin configuration required to
support parallel programming is shown in Figure 18. In this mode,
Ports 0 and 2 operate as the external address bus interface, P3
operates as the external data bus interface, and P1.0 operates as
the Write Enable strobe. Port 1.1, P1.2, P1.3, and P1.4 are used
as a general configuration port that configures the device for vari-
ous program and erase operations during parallel programming.
Table XIII. Flash/EE Memory Parallel Programming Modes
Port 1 Pins
P1.4 P1.3 P1.2 P1.1 Programming Mode
0 0 0 0 Erase Flash/EE Program,
Data, and Security Modes
1 0 0 1 Read Device Signature/ID
1 0 1 0 Program Code Byte
0 0 1 0 Program Data Byte
1 0 1 1 Read Code Byte
0 0 1 1 Read Data Byte
1 1 0 0 Program Security Modes
1 1 0 1 Read/Verify Security Modes
All other codes Redundant
V
DD
GND
P1.1 -> P1.4
PSEN
RESET
P3
P0
P2
ADuC836
5V
PROGRAM MODE
(SEE TABLE XIII)
GND
V
DD
PROGRAM
DATA
(D0–D7)
PROGRAM
ADDRESS
(A0–A13)
(P2.0 = A0)
(P1.7 = A13)
COMMAND
ENABLE
P1.0
EA
ENTRY
SEQUENCE
GND
P1.5 -> P1.7
TIMING
Figure 18. Flash/EE Memory Parallel Programming
REV. A
相關PDF資料
PDF描述
ADUC842BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP62-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP62-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP32-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
相關代理商/技術參數
參數描述
ADUC836BS 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS))
ADUC836BSZ 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
ADUC841 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC841BCP32-5 制造商:Analog Devices 功能描述:MICROCONVERTER 1-CYCLE VERSION ADUC829 - Trays
ADUC841BCP62-3 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 20MHZ 3.3V 56LFCSP - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*