參數資料
型號: ADT7463ARQZ-REEL
廠商: ON Semiconductor
文件頁數: 37/50頁
文件大小: 726K
描述: IC REMOTE THERMAL CTRLR 24-QSOP
產品變化通告: MFG CHG Notification ADI to ON Semi
QSOP 24ld Pkg (MSL) Change 17/Jun/2010
標準包裝: 2,500
系列: dBCool®
功能: 風扇控制,溫度監控器
傳感器類型: 內部和外部
感應溫度: -40°C ~ 120°C,外部傳感器
精確度: ±1.5°C(最小值)
拓?fù)洌?/td> ADC,比較器,風扇速度計數器,多路復用器,寄存器庫
輸出類型: SMBus?
輸出警報: 無
輸出風扇:
電源電壓: 3 V ~ 5.5 V
工作溫度: -40°C ~ 120°C
安裝類型: 表面貼裝
封裝/外殼: 24-SSOP(0.154",3.90mm 寬)
供應商設備封裝: 24-QSOP
包裝: 帶卷 (TR)
ADT7463
http://onsemi.com
37
Table 50. OPERATING POINT REGISTERS (POWERON DEFAULT = 0X64) (Note 1)
Register Address
R/W
Description
0x33
R/W
Remote 1 Operating Point Register (Default = 100癈)
0x34
R/W
Local Temp Operating Point Register (Default = 100癈)
0x35
R/W
Remote 2 Operating Point Register (Default = 100癈)
1.  These registers become readonly when the Configuration Register 1 lock bit is set to 1. Any subsequent attempts to write to these registers
will fail. These registers set the target operating point for each temperature channel when the dynamic T
MIN
 control feature is enabled. The
fans being controlled are adjusted to maintain temperature about an operating point.
Table 51. REGISTER 0X36  DYNAMIC T
MIN
 CONTROL REGISTER 1 (POWERON DEFAULT = 0X00) (Note 1)
Bit
Name
R/W
Description
<0>
CYR2
R/W
MSB of 3bit Remote 2 Cycle Value. The other two bits of the code reside in Dynamic T
MIN
Control Register 2 (Reg. 0x37). These three bits define the delay time between making
subsequent T
MIN
 adjustments in the control loop, in terms of number of monitoring cycles. The
system has associated thermal time constants that need to be found to optimize the response
of fans and the control loop.
<1>
V
CCP
LO
R/W
V
CCP
LO = 1. When the power is supplied from 3.3 V STANDBY and the core voltage (V
CCP
)
drops below its V
CCP
 low limit value (Reg. 0x46), the following occurs:
" Status Bit 1 in Status Register 1 gets set
" SMBALERT
 gets generated if enabled
" PROCHOT
 monitoring is disabled
" Dynamic T
MIN
 control is disabled
" The device is prevented from entering shutdown
" Everything reenabled once V
CCP
 increases above V
CCP
 low limit
<2>
PHTR1
R/W
PHTR1 = 1 copies the Remote 1 current temperature to the Remote 1 Operating Point Register
if THERM
 is asserted. The operating point contains the temperature at which THERM
 is
asserted. This allows the system to run as quietly as possible without affecting system
performance.
PHTR1 = 0 ignores any THERM
 assertions on the THERM
 pin. The Remote 1 Operating Point
Tegister reflects its programmed value.
<3>
PHTL
R/W
PHTL = 1 copies the local channels current temperature to the Local Operating Point Register
if THERM
 is asserted. The operating point contains the temperature at which THERM
 is
asserted. This allows the system to run as quietly as possible without affecting system
performance.
PHTL = 0 ignores any THERM
 assertions on the THERM
 pin. The Local Temperature
Operating Point Register reflects its programmed value.
<4>
PHTR2
R/W
PHTR2 = 1 copies the Remote 2 current temperature to the Remote 2 Operating Point Register
if THERM
 is asserted. The operating point contains the temperature at which THERM
 is
asserted. This allows the system to run as quietly as possible without system performance
being affected.
PHTR2 = 0 ignores any THERM
 assertions on the THERM
 pin. The Remote 2 Operating Point
Register reflects its programmed value.
<5>
R1T
R/W
R1T = 1 enables dynamic T
MIN
 control on the Remote 1 Temperature channel. The chosen
T
MIN
 value is dynamically adjusted based on the current temperature, operating point, and high
and low limits for this zone.
R1T = 0 disables dynamic T
MIN
 control. The T
MIN
 value chosen is not adjusted, and the
channel behaves as described in the Automatic Fan Control section.
<6>
LT
R/W
LT = 1 enables dynamic T
MIN
 control on the Local Temperature channel. The chosen T
MIN
value is dynamically adjusted based on the current temperature, operating point, and high and
low limits for this zone.
LT = 0 disables dynamic T
MIN
 control. The T
MIN
 value chosen is not adjusted, and the channel
behaves as described in the Automatic Fan Control section.
<7>
R2T
R/W
R2T = 1 enables dynamic T
MIN
 control on the Remote 2 Temperature channel. The chosen
T
MIN
 value is dynamically adjusted based on the current temperature, operating point, and high
and low limits for this zone.
R2T = 0 disables dynamic T
MIN
 control. The T
MIN
 value chosen is not adjusted, and the
channel behaves as described in the Automatic Fan Control section.
1.  This register becomes readonly when the Configuration Register 1 Lock bit is set to 1. Further attempts to write to this register have no effect.
相關PDF資料
PDF描述
ADT7476AARQZ-R IC REMOTE THERMAL CTLR 24QSOP
ADT7481ARMZ-1RL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7482ARMZ-REEL IC SENSOR TEMP 2CH ALARM 10MSOP
ADT7485AARMZ-R IC TEMP/VOLT DGL SENS SST 10MSOP
ADT7486AARMZ-RL IC TEMP SENS DGTL 2CH SST 10MSOP
相關代理商/技術參數
參數描述
ADT7463ARQZ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓?fù)?ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADT7466 制造商:AD 制造商全稱:Analog Devices 功能描述:dBCool Remote Thermal Controller and Voltage Monitor
ADT7466ARQZ 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7466ARQZ-REEL 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7466ARQZ-REEL7 功能描述:IC REMOTE THERMAL CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統(傳感器) 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C,外部傳感器 精確度:±2.5°C 本地(最大值),±5°C 遠程(最大值) 拓?fù)?ADC,比較器,寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6