- 您現在的位置：買賣IC網 > PDF目錄223308 > ADE7878ACPZ-RL (ANALOG DEVICES INC) Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind PDF資料下載
參數資料
| 型號： | ADE7878ACPZ-RL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, QCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, MO-220WJJD, LFCSP-40 |
| 文件頁數： | 18/96頁 |
| 文件大小： | 1096K |
| 代理商： | ADE7878ACPZ-RL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
ADE7854/ADE7858/ADE7868/ADE7878
Rev. E | Page 25 of 96
HARDWARE RESET
The ADE7854/ADE7858/ADE7868/ADE7878 each has a
RESET pin. If the ADE7854, ADE7858, ADE7868, or ADE7878
is in PSM0 mode and the RESET pin is set low, then the
ADE78xx enters the hardware reset state. The ADE78xx must
be in PSM0 mode for a hardware reset to be considered. Setting
the RESET pin low while the ADE78xx is in PSM1, PSM2, and
PSM3 modes does not have any effect.
If the ADE7854, ADE7858, ADE7868, or ADE7878 is in PSM0
mode and the RESET pin is toggled from high to low and then
back to high after at least 10 μs, all the registers are set to their
default values, including the CONFIG2 and LPOILVL registers.
The ADE78xx signals the end of the transition period by triggering
the IRQ1 interrupt pin low and setting Bit 15 (RSTDONE) in the
STATUS1 register to 1. This bit is 0 during the transition period
and becomes 1 when the transition ends. The status bit is cleared
and the IRQ1 pin is returned high by writing to the STATUS1
register with the corresponding bit set to 1.
After a hardware reset, the DSP is in idle mode, which means it
does not execute any instruction.
Because the I2C port is the default serial port of the ADE7854/
ADE7858/ADE7868/ADE7878, it becomes active after a reset
state. If SPI is the port used by the external microprocessor, the
procedure to enable it must be repeated immediately after the
RESET pin is toggled back to high (see the
section for details).
At this point, it is recommended to initialize all of the ADE78xx
registers, enable data memory RAM protection, and then write
0x0001 into the run register to start the DSP. See the Digital
Signal Processor section for details on data memory RAM
protection and the run register.
SOFTWARE RESET FUNCTIONALITY
Bit 7 (SWRST) in the CONFIG register manages the software
reset functionality in PSM0 mode. The default value of this bit is 0.
If this bit is set to 1, then the ADE7854/ADE7858/ADE7868/
internal registers are set to their default values. In addition, the
choice of which serial port, I2C or SPI, is in use remains unchanged
if the lock-in procedure has been executed previously (see the
Serial Interfaces for details). The registers that maintain their
values despite the SWRST bit being set to 1 are the CONFIG2
and LPOILVL registers. When the software reset ends, Bit 7
(SWRST) in the CONFIG register is cleared to 0, the IRQ1
interrupt pin is set low, and Bit 15 (RSTDONE) in the STATUS1
register is set to 1. This bit is 0 during the transition period and
becomes 1 when the transition ends. The status bit is cleared and
the IRQ1 pin is set back high by writing to the STATUS1 register
with the corresponding bit set to 1.
After a software reset ends, the DSP is in idle mode, which
means it does not execute any instruction. It is recommended
to initialize all the ADE7854/ADE7858/ADE7868/ADE7878
registers and then enable the data memory RAM protection and
write 0x0001 into the run register to start the DSP (see the
Digital Signal Processor section for details on data memory
RAM protection and the run register).
Software reset functionality is not available in PSM1, PSM2, or
PSM3 mode.
相關PDF資料 |
PDF描述 |
|---|---|
| ADG529FTQ | 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, CDIP18 |
| ADJ24006 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.042A (COIL), 6VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24012 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.021A (COIL), 12VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24024 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.01A (COIL), 24VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
| ADJ24048 | POWER/SIGNAL RELAY, SPST, LATCHED, 0.005A (COIL), 48VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADE7878XCPZ | 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk |
| ADE7880 | 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE |
| ADE7880ACPZ | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7880ACPZ-RL | 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:* |
| ADE7903ARWZ | 功能描述:Energy Monitor (Power Meter) 24 bit SPI 20-SOIC 制造商:analog devices inc. 系列:- 包裝:管件 零件狀態:有效 類型:能量監測器（功率計） 分辨率（位）:24 b 采樣率（每秒）:- 數據接口:SPI 電壓源:單電源 電壓 - 電源:2.97 V ~ 3.63 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:20-SOIC 標準包裝:37 |
發布緊急采購，3分鐘左右您將得到回復。