- 您現在的位置：買賣IC網 > PDF目錄1981 > AD7451BRMZ (Analog Devices Inc)IC ADC 12BIT DIFF 1MSPS 8MSOP PDF資料下載
參數資料
| 型號： | AD7451BRMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT DIFF 1MSPS 8MSOP |
| 標準包裝： | 50 |
| 位數： | 12 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 9.25mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個偽差分，單極 |
AD7441/AD7451
Rev. D | Page 14 of 24
TYPICAL CONNECTION DIAGRAM
Figure 22 shows a typical connection diagram for the device.
In this setup, the GND pin is connected to the analog ground
a 2.5 V decoupled reference source. The signal source is connected
to the VIN+ analog input via a unity gain buffer. A dc voltage is
connected to the VIN– pin to provide a pseudo ground for the
VIN+ input. The VDD pin is decoupled to AGND with a 10 μF
tantalum capacitor in parallel with a 0.1 μF ceramic capacitor.
The reference pin is decoupled to AGND with a capacitor of at
least 0.1 μF. The conversion result is output in a 16-bit word
with four leading zeros followed by the MSB of the 12-bit or
10-bit result. The 10-bit result of the AD7441 is followed by two
trailing zeros.
AD7441/
AD7451
0.1F
10F
VREF
VDD
DC INPUT
VOLTAGE
VIN+
SCLK
2.7V TO 5.25V
SUPPLY
SERIAL
INTERFACE
C/P
SDATA
CS
GND
VIN–
2.5V
AD780
VREF
p-p
03
15
3-
0
22
Figure 22. Typical Connection Diagram
ANALOG INPUT
The AD7441/AD7451 have a pseudo differential analog input.
The VIN+ input is coupled to the signal source and must have an
amplitude of VREF p-p to make use of the full dynamic range of
the part. A dc input is applied to the VIN–. The voltage applied to
this input provides an offset from ground or a pseudo ground
for the VIN+ input. Pseudo differential inputs separate the analog
input signal ground from the ADC ground, allowing dc common-
mode voltages to be cancelled.
Because the ADC operates from a single supply, it is necessary
to level shift ground-based bipolar signals to comply with the
input requirements. An op amp (for example, the AD8021) can
be configured to rescale and level shift a ground-based (bipolar)
signal so that it is compatible with the input range of the AD7441/
AD7451 (see Figure 23).
When a conversion takes place, the pseudo ground corresponds
to 0, and the maximum analog input corresponds to 4096 for
the AD7451 and 1024 for the AD7441.
R
2.5V
1.25V
0V
+1.25V
0V
–1.25V
R
3R
0.1F
R
AD7441/
AD7451
VIN+
VIN–
VREF
EXTERNAL
VREF (2.5V)
0
31
53
-0
23
Figure 23. Op Amp Configuration to Level Shift a Bipolar Input Signal
ANALOG INPUT STRUCTURE
Figure 24 shows the equivalent circuit of the analog input
structure of the AD7441/AD7451. The four diodes provide
ESD protection for the analog inputs. Care must be taken to
ensure that the analog input signals never exceed the supply
rails by more than 300 mV. This causes these diodes to become
forward-biased and start conducting into the substrate. These
diodes can conduct up to 10 mA without causing irreversible
damage to the part. The C1 capacitors (see Figure 24) are
typically 4 pF and can be attributed primarily to pin capaci-
tance. The resistors are lumped components made up of
the on resistance of the switches. The value of these resistors
is typically about 100 Ω. The C2 capacitors are the ADC
sampling capacitors and have a capacitance of 16 pF typically.
For ac applications, removing high frequency components from
the analog input signal through the use of an RC low-pass filter
on the relevant analog input pins is recommended. In applica-
tions where harmonic distortion and the signal-to-noise ratio
are critical, it is recommended that the analog input be driven
from a low impedance source. Large source impedances
significantly affect the ac performance of the ADC, which can
necessitate the use of an input buffer amplifier. The choice of
the amplifier is a function of the particular application.
C1
C2
R1
D
C1
C2
R1
D
VDD
VIN+
VIN–
03
15
3-
02
4
Figure 24. Equivalent Analog Input Circuit;
Conversion Phase—Switches Open;
Track Phase—Switches Closed
相關PDF資料 |
PDF描述 |
|---|---|
| AD7452BRT-R2 | IC ADC 12BIT 555KSPS SOT23-8 |
| AD7453BRTZ-REEL7 | IC ADC 12BIT W/DIFF INP SOT23-8 |
| AD7457BRTZ-REEL7 | IC ADC 12BIT PSEUDO-DIFF SOT23-8 |
| AD7467BRTZ-REEL | IC ADC 10BIT 1.6V MCRPWR SOT23-6 |
| AD7472ARU-REEL | IC ADC 12BIT PARALLEL 24-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7451BRMZ | 制造商:Analog Devices 功能描述:12BIT SAR ADC DIFF I/P SMD 7451 |
| AD7451BRT | 制造商:AD 制造商全稱:Analog Devices 功能描述:Pseudo Differential, 1MSPS, 12- & 10-Bit ADCs in 8-lead SOT-23 |
| AD7451BRT-R2 | 功能描述:IC ADC 12BIT W/DIFF INP SOT-23-8 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7451BRT-REEL7 | 制造商:Analog Devices 功能描述: |
| AD7452 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential Input, 555 kSPS 12-Bit ADC in an 8-Lead SOT-23 |
發布緊急采購，3分鐘左右您將得到回復。