UP WITH VIN
鍙冩暩(sh霉)璩囨枡
鍨嬭櫉锛� AD7451BRMZ
寤犲晢锛� Analog Devices Inc
鏂囦欢闋佹暩(sh霉)锛� 13/25闋�
鏂囦欢澶�?銆�?/td> 0K
鎻忚堪锛� IC ADC 12BIT DIFF 1MSPS 8MSOP
妯�(bi膩o)婧�(zh菙n)鍖呰锛� 50
浣嶆暩(sh霉)锛� 12
閲囨ǎ鐜囷紙姣忕锛夛細 1M
鏁�(sh霉)鎿�(j霉)鎺ュ彛锛� DSP锛孧ICROWIRE?锛孮SPI?锛屼覆琛�锛孲PI?
杞�(zhu菐n)鎻涘櫒鏁�(sh霉)鐩細 1
鍔熺巼鑰楁暎锛堟渶澶э級锛� 9.25mW
闆诲闆绘簮锛� 鍠浕婧�
宸ヤ綔婧害锛� -40°C ~ 85°C
瀹夎椤炲瀷锛� 琛ㄩ潰璨艰
灏佽/澶栨锛� 8-TSSOP锛�8-MSOP锛�0.118"锛�3.00mm 瀵級
渚涙噳(y墨ng)鍟嗚ō(sh猫)鍌欏皝瑁濓細 8-MSOP
鍖呰锛� 绠′欢
杓稿叆鏁�(sh霉)鐩拰椤炲瀷锛� 1 鍊嬪伣宸垎锛屽柈妤�
AD7441/AD7451
Rev. D | Page 19 of 24
CS
SCLK
SDATA
1
10
16
1
10
16
A
THIS PART IS FULLY POWERED
UP WITH VIN FULLY ACQUIRED
PART BEGINS
TO POWER UP
INVALID DATA
VALID DATA
tPOWER-UP
03
15
3-
0
31
Figure 31. Exiting Power-Down Mode
If CS is brought high before the 10th falling edge of SCLK, the
AD7441/AD7451 again go back into power-down. This avoids
accidental power-up due to glitches on the CS line or an inad-
vertent burst of eight SCLK cycles while CS is low. So although
the device may begin to power up on the falling edge of CS, it
again powers down on the rising edge of CS as long as it occurs
before the 10th SCLK falling edge.
Power-Up Time
The power-up time of the AD7441/AD7451 is typically 1 渭s,
which means that with any frequency of SCLK up to 18 MHz,
one dummy cycle is always sufficient to allow the device to
power up. Once the dummy cycle is complete, the ADC is fully
powered up and the input signal is acquired properly. The quiet
time, tQUIET, must still be allowed鈥攆rom the point at which the
bus goes back into three-state after the dummy conversion to
the next falling edge of CS.
When running at the maximum throughput rate of 1 MSPS,
the AD7441/AD7451 power up and acquire a signal within
卤0.5 LSB in one dummy cycle, that is, 1 渭s. When powering up
from the power-down mode with a dummy cycle, as in Figure 31,
the track-and-hold, which was in hold mode while the part was
powered down, returns to track mode after the first SCLK edge
the part receives after the falling edge of CS. This is shown as
Point A in
Although at any SCLK frequency one dummy cycle is sufficient
to power up the device and acquire VIN, it does not necessarily
mean that a full dummy cycle of 16 SCLKs must always elapse
to power up the device and acquire VIN fully; 1 渭s is sufficient to
power up the device and acquire the input signal.
For example, when a 5 MHz SCLK frequency is applied to the
ADC, the cycle time is 3.2 渭s (that is, 1/(5 MHz) 脳 16). In one
dummy cycle, 3.2 渭s, the part is powered up, and VIN is acquired
fully. However, after 1 渭s with a five MHz SCLK, only five SCLK
cycles elapse. At this stage, the ADC is fully powered up and the
signal acquired. Therefore, in this case, the CS can be brought
high after the 10th SCLK falling edge and brought low again
after a time, tQUIET, to initiate the conversion.
When power supplies are first applied to the AD7441/AD7451,
the ADC can power up either in power-down mode or normal
mode. For this reason, it is best to allow a dummy cycle to elapse
to ensure that the part is fully powered up before attempting a
valid conversion. Likewise, if the user wants the part to power
up in power-down mode, then the dummy cycle can be used to
ensure the device is in power-down mode by executing a cycle
such as that shown in Figure 30. Once supplies are applied to
the AD7441/AD7451, the power-up time is the same as that
when powering up from power-down mode. It takes approxi-
mately 1 渭s to power up fully in normal mode. It is not necessary
to wait 1 渭s before executing a dummy cycle to ensure the
desired mode of operation. Instead, the dummy cycle can
occur directly after power is supplied to the ADC. If the first
valid conversion is then performed directly after the dummy
conversion, care must be taken to ensure that adequate
acquisition time has been allowed.
As mentioned earlier, when powering up from the power-down
mode, the part returns to track mode upon the first SCLK edge
applied after the falling edge of CS. However, when the ADC
powers up initially after supplies are applied, the track-and-
hold is already in track mode. This means (assuming one has
the facility to monitor the ADC supply current) that if the ADC
powers up in the desired mode of operation, a dummy cycle is
not required to change mode. Thus, a dummy cycle is also not
required to place the track-and-hold into track.
鐩搁棞(gu膩n)PDF璩囨枡
PDF鎻忚堪
AD7452BRT-R2 IC ADC 12BIT 555KSPS SOT23-8
AD7453BRTZ-REEL7 IC ADC 12BIT W/DIFF INP SOT23-8
AD7457BRTZ-REEL7 IC ADC 12BIT PSEUDO-DIFF SOT23-8
AD7467BRTZ-REEL IC ADC 10BIT 1.6V MCRPWR SOT23-6
AD7472ARU-REEL IC ADC 12BIT PARALLEL 24-TSSOP
鐩搁棞(gu膩n)浠g悊鍟�/鎶€琛�(sh霉)鍙冩暩(sh霉)
鍙冩暩(sh霉)鎻忚堪
AD7451BRMZ 鍒堕€犲晢:Analog Devices 鍔熻兘鎻忚堪:12BIT SAR ADC DIFF I/P SMD 7451
AD7451BRT 鍒堕€犲晢:AD 鍒堕€犲晢鍏ㄧū:Analog Devices 鍔熻兘鎻忚堪:Pseudo Differential, 1MSPS, 12- & 10-Bit ADCs in 8-lead SOT-23
AD7451BRT-R2 鍔熻兘鎻忚堪:IC ADC 12BIT W/DIFF INP SOT-23-8 RoHS:鍚� 椤炲垾:闆嗘垚闆昏矾 (IC) >> 鏁�(sh霉)鎿�(j霉)閲囬泦 - 妯℃暩(sh霉)杞�(zhu菐n)鎻涘櫒 绯诲垪:- 鐢�(ch菐n)鍝佸煿瑷�(x霉n)妯″:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 妯�(bi膩o)婧�(zh菙n)鍖呰:2,500 绯诲垪:- 浣嶆暩(sh霉):12 閲囨ǎ鐜囷紙姣忕锛�:3M 鏁�(sh霉)鎿�(j霉)鎺ュ彛:- 杞�(zhu菐n)鎻涘櫒鏁�(sh霉)鐩�:- 鍔熺巼鑰楁暎锛堟渶澶э級:- 闆诲闆绘簮:- 宸ヤ綔婧害:- 瀹夎椤炲瀷:琛ㄩ潰璨艰 灏佽/澶栨:SOT-23-6 渚涙噳(y墨ng)鍟嗚ō(sh猫)鍌欏皝瑁�:SOT-23-6 鍖呰:甯跺嵎 (TR) 杓稿叆鏁�(sh霉)鐩拰椤炲瀷:-
AD7451BRT-REEL7 鍒堕€犲晢:Analog Devices 鍔熻兘鎻忚堪:
AD7452 鍒堕€犲晢:AD 鍒堕€犲晢鍏ㄧū:Analog Devices 鍔熻兘鎻忚堪:Differential Input, 555 kSPS 12-Bit ADC in an 8-Lead SOT-23