參數資料
型號： AD5757ACPZ
廠商： Analog Devices Inc
文件頁數： 4/44頁
文件大?。?/td> 0K
描述： IC DAC 16BIT QUAD 64-LFCSP
特色產品： AD5755 / AD5755-1 / AD5757 DACs
標準包裝： 1
設置時間： 15µs
位數： 16
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 4
電壓電源： 模擬和數字
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤，CSP
供應商設備封裝： 64-LFCSP-VQ（9x9）
包裝： 管件
輸出數目和類型： *
采樣率（每秒）： *
AD5757
Data Sheet
Rev. D | Page 12 of 44
Pin No.
Mnemonic
Description
15
ALERT
Active High Output. This pin is asserted when there has been no SPI activity on the interface pins for a
predetermined time. See the Device Features section for more information.
16
FAULT
Active Low Output. This pin is asserted low when an open circuit in current mode is detected, a short circuit in
voltage mode is detected, a PEC error is detected, or an overtemperature is detected (see the Device Features
section). Open-drain output.
18
RESET
Hardware Reset. Active Low Input.
19
AV
DD
Positive Analog Supply. The voltage range is from 10.8 V to 33 V.
20, 25,
28, 30,
50, 52,
55, 60
NC
No Connect. Do not connect to this pin.
21
CHARTA
HART Input Connection for DAC Channel A.
22
IGATEA
Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter. See
the External PMOS Mode section for more information.
23
COMP
DCDC_A
DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the
feedback loop of the Channel A dc-to-dc converter. Alternatively, if using an external compensation resistor,
place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation
information).
24
V
BOOST_A
Supply for Channel A Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as
26
I
OUT_A
Current Output Pin for DAC Channel A.
27, 40, 53
AGND
Ground Reference Point for Analog Circuitry. This must be connected to 0 V.
29
CHARTB
HART Input Connection for DAC Channel B.
31
IGATEB
Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter.
See the External PMOS Mode section for more information.
32
COMP
DCDC_B
DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the
feedback loop of the Channel B dc-to-dc converter. Alternatively, if using an external compensation resistor,
place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation
information).
33
I
OUT_B
Current Output Pin for DAC Channel B.
34
V
BOOST_B
Supply for Channel B Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as
35
AGND
Ground Reference Point for Analog Circuitry. This pin must be connected to 0 V.
36
SW
B
Switching Output for Channel B DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
37
GNDSW
B
Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground.
38
GNDSW
A
Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground.
39
SW
A
Switching Output for Channel A DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
41
SW
D
Switching Output for Channel D DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
42
GNDSW
D
Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground.
43
GNDSW
C
Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground.
44
SW
C
Switching Output for Channel C DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
45
AV
CC
Supply for DC-to-DC Circuitry.
46
V
BOOST_C
Supply for Channel C Current Output Stage (see Figure 49). To use the dc-to-dc feature of the device, connect as
47
I
OUT_C
Current Output Pin for DAC Channel C.
48
COMP
DCDC_C
DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the
feedback loop of the Channel C dc-to-dc converter. Alternatively, if using an external compensation resistor,
place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation
information).
49
IGATEC
Optional Connection for External Pass Transistor. Should be left unconnected when using the dc-to-dc converter. See
the External PMOS Mode section for more information.
相關PDF資料
PDF描述
MS3122E16-23S CONN RCPT 23POS BOX MNT W/SCKT
MS27497T18A32PLC CONN HSG RCPT 32POS WALL MT PINS
AD7225KNZ IC DAC 8BIT QUAD W/AMP 24DIP
VE-2WL-MY-F4 CONVERTER MOD DC/DC 28V 50W
AD7537KRZ IC DAC 12BIT DUAL MULT 24SOIC
相關代理商/技術參數
參數描述
AD5757ACPZ-REEL7 功能描述:IC DAC 16BIT QUAD IOUT 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k
AD5757X 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA Output DAC, Dynamic Power Control, HART Connectivity
AD575JD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit
AD575JN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit
AD575KD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*