- 您現在的位置：買賣IC網 > PDF目錄165342 > AD5757ACPZ-REEL7 (ANALOG DEVICES INC) SERIAL INPUT LOADING, 15 us SETTLING TIME, 16-BIT DAC, QCC64 PDF資料下載
參數資料
| 型號： | AD5757ACPZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | SERIAL INPUT LOADING, 15 us SETTLING TIME, 16-BIT DAC, QCC64 |
| 封裝： | 9 X 9 MM, ROHS COMPLIANT, MO-220VMMD-4, LFCSP-64 |
| 文件頁數： | 29/44頁 |
| 文件大小： | 1122K |
| 代理商： | AD5757ACPZ-REEL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD5757
Rev. A | Page 35 of 44
Digitally controlling the slew rate of the output is necessary to
meet the analog rate of change requirements for HART.
DIGITAL SLEW RATE CONTROL
The slew rate control feature of the AD5757 allows the user to
control the rate at which the output value changes. With the
slew rate control feature disabled, the output value changes at a
rate limited by the output drive circuitry and the attached load.
To reduce the slew rate, this can be achieved by enabling the
slew rate control feature. With the feature enabled via the SREN
bit of the slew rate control register (see Table 25), the output,
instead of slewing directly between two values, steps digitally at
a rate defined by two parameters accessible via the slew rate
control register, as shown in Table 25. The parameters are
SR_CLOCK and SR_STEP. SR_CLOCK defines the rate at
which the digital slew is updated, for example, if the selected
update rate is 8 kHz, the output updates every 125 μs. In conjunc-
tion with this, SR_STEP defines by how much the output value
changes at each update. Together, both parameters define the
the range of values for both the SR_CLOCK and SR_STEP
parameters.
Table 31. Slew Rate Update Clock Options
SR_CLOCK
Update Clock Frequency (Hz)1
0000
64 k
0001
32 k
0010
16 k
0011
8 k
0100
4 k
0101
2 k
0110
1 k
0111
500
1000
250
1001
125
1010
64
1011
32
1100
16
1101
8
1110
4
1111
0.5
1 These clock frequencies are divided down from the 13 MHz internal
Table 32. Slew Rate Step Size Options
SR_STEP
Step Size (LSBs)
000
1
001
2
010
4
011
16
100
32
101
64
110
128
111
256
The following equation describes the slew rate as a function of
the step size, the update clock frequency, and the LSB size:
Size
LSB
Frequency
Clock
Update
Size
Step
Change
Output
Time
Slew
×
=
where:
Slew Time
is expressed in seconds.
Output Change
is expressed in amps for IOUT_x.
When the slew rate control feature is enabled, all output
changes occur at the programmed slew rate (see the DC-to-DC
Converter Settling Time section for additional information).
For example, if the CLEAR pin is asserted, the output slews to
the clear value at the programmed slew rate (assuming that the
clear channel is enabled to be cleared). If a number of channels
are enabled for slew, care must be taken when asserting the
CLEAR pin. If one of the channels is slewing when CLEAR is
asserted, other channels may change directly to their clear
values not under slew rate control. The update clock frequency
for any given value is the same for all output ranges. The step
size, however, varies across output ranges for a given value of
step size because the LSB size is different for each output range.
POWER DISSIPATION CONTROL
The AD5757 contains integrated dynamic power control using
a dc-to-dc boost converter circuit, allowing reductions in power
consumption from standard designs.
In standard current input module designs, the load resistor
values can range from typically 50 Ω to 750 Ω. Output module
systems must source enough voltage to meet the compliance
voltage requirement across the full range of load resistor values.
For example, in a 4 mA to 20 mA loop when driving 20 mA, a
compliance voltage of >15 V is required. When driving 20 mA
into a 50 Ω load, only 1 V compliance is required.
The AD5757 circuitry senses the output voltage and regulates
this voltage to meet compliance requirements plus a small
headroom voltage. The AD5757 is capable of driving up to
24 mA through a 1 kΩ load.
DC-TO-DC CONVERTERS
The AD5757 contains four independent dc-to-dc converters.
These are used to provide dynamic control of the VBOOST supply
discreet components needed for the dc-to-dc circuitry, and the
following sections describe component selection and operation
of this circuitry.
AVCC
LDCDC
DDCDC
CDCDC
4.7F
CFILTER
0.1F
RFILTER
CIN
SWx
VBOOST_X
≥10F
10
10H
09225
-077
Figure 56. DC-to-DC Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| AD5757ACPZ | SERIAL INPUT LOADING, 15 us SETTLING TIME, 16-BIT DAC, QCC64 |
| AD590-02 | ANALOG TEMP SENSOR-CURRENT, 298.2uA, RECTANGULAR, THROUGH HOLE MOUNT |
| AD632TH/883 | ANALOG MULTIPLIER OR DIVIDER, MBCY10 |
| AD670JNZ | 2-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDIP20 |
| AD706JRZ | Dual Picoampere Input Current Bipolar Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5757X | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA Output DAC, Dynamic Power Control, HART Connectivity |
| AD575JD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
| AD575JN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
| AD575KD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
| AD575KN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit |
發布緊急采購，3分鐘左右您將得到回復。