參數資料
型號： 935262056518
廠商： NXP SEMICONDUCTORS
元件分類： 尋呼電路
英文描述： TELECOM, PAGING DECODER, PQFP32
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-358-1, LQFP-32
文件頁數： 76/76頁
文件大?。?/td> 301K
代理商： 935262056518
1999 Apr 12
9
Philips Semiconductors
Product specication
FLEX
roaming decoder II
PCD5013
8.3
Serial Peripheral Interface (SPI)
8.3.1
GENERAL
All data communication between the PCD5013 and the
host is done via the SPI using 32-bit data packets at data
rates up to 1 Mbits/s. SPI transfers are full-duplex and can
be initiated by either the host which acts as the SPI master
providing the data clock for packet transfer, or the
PCD5013 as an SPI slave.
The host can send packets to configure or control the
PCD5013 or a checksum packet to validate SPI
communication (Section 8.4.2). The PCD5013 buffers
data packets, relating to received data, into a 32 packet
transmit buffer. The PCD5013 can send either a status
packet, a part ID packet, or packets from the transmit
buffer. In the event of a buffer overflow, the PCD5013
stops decoding and clears the transmit buffer.
8.3.2
SPI INTERCONNECT
Connection on the PCD5013 consists of a READY pin and
4 SPI pins (SS, SCK, MOSI and MISO):
READY: output signal; indicates that data is available
from the PCD5013
SS: SPI select; used as PCD5013 chip select
SCK: serial clock; output from the host used for clocking
data
MOSI: master output slave input; data output from the
host
MISO: master input slave output; data output from the
PCD5013.
8.3.3
SPI TRANSFER INITIATED BY THE HOST
The following steps occur when the host initiates an SPI
packet transfer, see Fig.5 for event timings:
1. The host selects the PCD5013 by driving the
SS pin LOW.
2. The PCD5013 indicates that it is ready to start the
SPI transfer by driving the READY pin LOW.
3. The host clocks each of the 32 bits of the SPI packet
by pulsing SCK. Both the host and the PCD5013
sample data on the rising edge of SCK. Packets are
sent MSB first.
4. The PCD5013 pulls the READY line HIGH, to indicate
that the transfer is complete.
5. The host waits until the READY line is pulled HIGH,
then de-selects the PCD5013 SPI by driving the
SS pin HIGH.
6. The first 5 steps are repeated for each additional
packet.
8.3.4
SPI TRANSFER INITIATED BY THE DECODER
The following steps occur when the PCD5013 initiates an
SPI packet transfer, see Fig.6 for event timings:
1. The PCD5013 initiates the SPI transfer by driving the
READY pin LOW.
2. If the PCD5013 is not already selected, the host
selects the PCD5013 SPI by driving the SS pin LOW.
3. The host clocks each of the 32 bits of the SPI packet
by pulsing SCK. Both the host and the PCD5013
sample data on the rising edge of SCK. Packets are
sent MSB first.
4. The PCD5013 pulls the READY line HIGH, to indicate
that the transfer is complete.
5. The host may then either de-select the SPI interface of
the PCD5013 (Fig.7) by driving the SS pin HIGH or
maintain SS LOW to continue sending packets to the
PCD5013.
相關PDF資料
PDF描述
935262079112 ALVT SERIES, 7-BIT DRIVER, TRUE OUTPUT, PDSO56
935262218112 0 TIMER(S), REAL TIME CLOCK, PDIP8
07683 MINI MOD SHIELD
07683-2 MINI MOD SHIELD
935262233112 16 I/O, PIA-GENERAL PURPOSE, PDSO24
相關代理商/技術參數
參數描述
935262217118 制造商:NXP Semiconductors 功能描述:Real Time Clock Serial 8-Pin SO T/R
935264217557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*