參數資料
型號： XRT83VL38IB-F
廠商： Exar Corporation
文件頁數： 13/95頁
文件大小： 0K
描述： IC LIU SH T1/E1/J1 OCTAL 225BGA
標準包裝： 84
類型： 線路接口裝置（LIU）
驅動器/接收器數： 8/8
規程： E1
電源電壓： 3.14 V ~ 3.47 V
安裝類型： 表面貼裝
封裝/外殼： 225-BGA
供應商設備封裝： 225-BGA（19x19）
包裝： 托盤
其它名稱： 1016-1481
XRT83VL38IB-F-ND
XRT83VL38
16
OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
ALARM FUNCTIONS/REDUNDANCY SUPPORT
SIGNAL NAME
LEAD #
TYPE
DESCRIPTION
GAUGE
J18
I
Twisted Pair Cable Wire Gauge Select - Hardware Mode
Connect this pin “High” to select 26 Gauge wire. Connect this pin “Low” to select 22
and 24 gauge wire for all channels.
NOTE: Internally pulled “Low” with a 50k
resistor.
DMO_0
DMO_1
DMO_2
DMO_3
DMO_4
DMO_5
DMO_6
DMO_7
D5
D4
C15
C13
R5
P4
U17
V14
O
Driver Failure Monitor Channel _0:
This pin transitions “High” if a short circuit condition is detected in the transmit driver of
Channel _0, or no transmit output pulse is detected for more than 128 TCLK_0 cycles.
Driver Failure Monitor Channel _1
Driver Failure Monitor Channel _2
Driver Failure Monitor Channel _3
Driver Failure Monitor Channel _4
Driver Failure Monitor Channel _5
Driver Failure Monitor Channel _6
Driver Failure Monitor Channel _7
ATAOS
PCLK/SCLK
T13
I
Automatic Transmit “All Ones” Pattern - Hardware Mode
A "High" level on this pin enables the automatic transmission of an "All Ones" AMI pat-
tern from the transmitter of any channel that the receiver of that channel has detected
an LOS condition. A "Low" level on this pin disables this function.
Note: All channels share the same ATAOS control function.
Microprocessor Clock Input - Host mode
NOTE: This pin is internally pulled “Low” for asynchronous microprocessor interface
when no clock is present.
TRATIO
INT
L16
I
O
Transmitter Transformer Ratio Select - Hardware mode
TRATIO is Not Supported in the 83VL38. This pin is for INT only..
Interrupt Output - Host mode
This pin is asserted “Low” to indicate an alarm condition.
NOTE: This pin is an open drain output and requires an external 10k
pull-up resistor.
RESET
T8
I
Hardware Reset (Active “Low”):
When this pin is tied “Low” for more than 10s, the device is put in the reset state.
Exar recommends initiating a Harware reset upon power up.
NOTE: This pin is internally pulled “High” with a 50k
resistor.
SR/DR
K4
I
Single-Rail/Dual-Rail Data Format:
Connect this pin “Low” to select transmit and receive data format in Dual-Rail mode.
In this mode, HDB3 or B8ZS encoder and decoder are not available.
Connect this pin “High” to select single-rail data format.
NOTE: Internally pulled “Low” with a 50k
resistor.
相關PDF資料
PDF描述
XRT83VSH28IB IC LIU SH E1 OCTAL 225BGA
XRT83VSH314IB-F IC LIU SH T1/E1/J1 14CH 304TBGA
XRT83VSH316IB IC LIU SH T1/E1/J1 16CH 316STBGA
XRT83VSH38IB IC LIU SH T1/E1/J1 8CH 225BGA
XRT85L61IG IC BITS CLOCK EXTRACTOR 28TSSOP
相關代理商/技術參數
參數描述
XRT83VSH28 制造商:EXAR 制造商全稱:EXAR 功能描述:8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
XRT83VSH28ES 功能描述:外圍驅動器與原件 - PCI 8 CH E1 LIU SH (low cost version) RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83VSH28IB 功能描述:接口 - 專用 8 Ch T1/E1 Framer RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT83VSH28IB-F 功能描述:外圍驅動器與原件 - PCI 8 Channel 1.8V-3.3V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83VSH28IB-F 制造商:Exar Corporation 功能描述:T1/E1 LIU IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*