- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83SL28IV (EXAR CORP) 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT83SL28IV |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144 |
| 文件頁數： | 7/47頁 |
| 文件大?。?/td> | 377K |
| 代理商： | XRT83SL28IV |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
xr
REV. 1.0.0
XRT83SL28
8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
5
PIN DESCRIPTIONS
HOST MODE INTERFACE
SERIAL MICROPROCESSOR INTERFACE
N
AME
P
IN
T
YPE
D
ESCRIPTION
CS
89
I
Chip Select Input
Active low signal. This signal enables the serial microprocessor interface by
pulling chip select "Low". The serial interface is disabled when the chip select
signal returns "High".
SCLK
90
I
Serial Clock Input
The serial clock input samples SDI on the rising edge and updates SDO on the
falling edge. See the Serial Microprocessor section of this datasheet for more
details.
SDI
92
I
Serial Data Input
The serial data input pin is used to supply an address and data string to pro-
gram the internal registers within the device. See the Serial Microprocessor
section of this datasheet for more details.
SDO
91
O
Serial Data Output
The serial data output pin is used to retrieve the internal contents of a selected
register in readback mode. See the Microprocessor section of this datasheet
for more details.
Reset
28
I
Hardware Reset Input
Active low signal. When this pin is pulled "Low" for more than 10μS, all internal
registers and state machines are set to their default state.
N
OTE
:
This pin must be pulled "High" to VDD for normal operation.
INT
100
O
Interrupt Output
Active low signal. This signal is asserted "Low" when a change in alarm status
occurs. Once the status registers have been read, the interrupt pin will return
"High". GIE (Global Interrupt Enable) must be set "High" in the appropriate
global register to enable interrupt generation.
N
OTE
:
This pin is an open-drain output that requires an external 10K
pull-up
resistor.
HW/Host
81
I
Hardware / Host Mode Select Input
This pin is used to select the mode of operation. By default, the LIU is config-
ured for Host mode. To select Hardware mode, this pin must be pulled "High".
N
OTE
:
Internally pulled "Low" with a 50k
resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL30 | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30IV | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VSH28 | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH28IB | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314 | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL28IV-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL30 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30ES | 功能描述:外圍驅動器與原件 - PCI 1 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL30IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30IV-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。