- 您現在的位置：買賣IC網 > PDF目錄376463 > XRT83SL28IV (EXAR CORP) 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT83SL28IV |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144 |
| 文件頁數： | 34/47頁 |
| 文件大小： | 377K |
| 代理商： | XRT83SL28IV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
XRT83SL28
8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
xr
REV. 1.0.0
32
4.2
The serial data input is sampled on the rising edge of SCLK. In read-back mode, the serial data output is
updated on the falling edge of SCLK. The serial data must be applied to the LIU LSB first. The 16 bits of serial
data are described below.
4.2.1
R/W (SCLK1)
The first serial bit applied to the LIU informs the microprocessor that a Read or Write operation is desired. If the
R/W bit is set to “0”, the microprocessor is configured for a Write operation. If the R/W bit is set to “1”, the
microprocessor is configured for a Read operation.
4.2.2
A[5:0] (SCLK2 - SCLK7)
The next 6 SCLK cycles are used to provide the address to which a Read or Write operation will occur. A0
(LSB) must be sent to the LIU first followed by A1 and so forth until all 6 address bits have been sampled by
SCLK.
4.2.3
X (Dummy Bit SCLK8)
The dummy bit sampled by SCLK8 is used to allow sufficient time for the serial data output pin to update data
if the read-back mode is selected by setting R/W = “1”. Therefore, the state of this bit is ignored and can hold
either “0” or “1” during both Read and Write operations.
4.2.4
D[7:0] (SCLK9 - SCLK16)
The next 8 SCLK cycles are used to provide the data to be written into the internal register chosen by the
address bits. D0 (LSB) must be sent to the LIU first followed by D1 and so forth until all 8 data bits have been
sampled by SCLK. Once 16 SCLK cycles have been complete, the LIU holds the data until CS is pulled “High”
whereby, the serial microprocessor latches the data into the selected internal register.
4.3
8-Bit Serial Data Output Description
The serial data output is updated on the falling edge of SCLK9 - SCLK16 if R/W is set to “1”. D0 (LSB) is
provided on SCLK9 to the SDO pin first followed by D1 and so forth until all 8 data bits have been updated. The
SDO pin allows the user to read the contents stored in individual registers by providing the desired address on
the SDI pin during the Read cycle.
16-Bit Serial Data Input Description
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83SL30 | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30IV | SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VSH28 | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH28IB | 8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83VSH314 | 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL28IV-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL30 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30ES | 功能描述:外圍驅動器與原件 - PCI 1 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL30IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL30IV-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。