INTEL
參數資料
型號： XRT83L314IB-L
廠商： Exar Corporation
文件頁數： 44/84頁
文件大小： 0K
描述： IC LIU T1/E1/J1 14CH 304TBGA
標準包裝： 27
類型： 線路接口裝置（LIU）
驅動器/接收器數： 14/14
規程： T1，E1，J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 304-LBGA
供應商設備封裝： 304-TBGA（31x31）
包裝： 托盤
XRT83L314
14-CHANNEL T1/E1/J1 LONG-HAUL/SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.0
45
5.2
INTEL MODE PROGRAMMED I/O ACCESS (ASYNCHRONOUS)
If the LIU is interfaced to an Intel type P, then it should be configured to operate in the Intel mode. Intel type
Read and Write operations are described below.
Intel Mode Read Cycle
Whenever an Intel-type P wishes to read the contents of a register, it should do the following.
1. Place the address of the target register on the address bus input pins ADDR[10:0].
2. While the P is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables further communication between the
P and the LIU microprocessor interface block.
3. Toggle the ALE input pin "High". This step enables the address bus input drivers, within the microproces-
sor interface block of the LIU.
4. The P should then toggle the ALE pin "Low". This step causes the LIU to latch the contents of the address
bus into its internal circuitry. At this point, the address of the register has now been selected.
5. Next, the P should indicate that this current bus cycle is a Read operation by toggling the RD input pin
"Low". This action also enables the bi-directional data bus output drivers of the LIU.
6. After the P toggles the Read signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
in order to inform the P that the data is available to be read by the P, and that it is ready for the next com-
mand.
7. After the P detects the RDY signal and has read the data, it can terminate the Read Cycle by toggling the
RD input pin "High".
NOTE: ALE can be tied “High” if this signal is not available.
The Intel Mode Write Cycle
Whenever an Intel type P wishes to write a byte or word of data into a register within the LIU, it should do the
following.
1. Place the address of the target register on the address bus input pins ADDR[10:0].
2. While the P is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables further communication between the
P and the LIU microprocessor interface block.
3. Toggle the ALE input pin "High". This step enables the address bus input drivers, within the microproces-
sor interface block of the LIU.
4. The P should then toggle the ALE pin "Low". This step causes the LIU to latch the contents of the address
bus into its internal circuitry. At this point, the address of the register has now been selected.
5. The P should then place the byte or word that it intends to write into the target register, on the bi-direc-
tional data bus DATA[7:0].
6. Next, the P should indicate that this current bus cycle is a Write operation by toggling the WR input pin
"Low". This action also enables the bi-directional data bus input drivers of the LIU.
7. After the P toggles the Write signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
in order to inform the P that the data has been written into the internal register location, and that it is ready
for the next command.
NOTE: ALE can be tied “High” if this signal is not available.
The Intel Read and Write timing diagram is shown in Figure 42. The timing specifications are shown in
相關PDF資料
PDF描述
XRT83L34IV-F IC LIU T1/E1/J1 QUAD 128TQFP
XRT83L38IB-F IC LIU T1/E1/J1 OCTAL 225BGA
XRT83SH314IB-F IC LIU T1/E1/J1 14CH 304TBGA
XRT83SH38IB-F IC LIU SH T1/E1/J1 8CH 225BGA
XRT86L30IV-F IC LIU/FRAMER TI/E1/J1 SGL 128LQ
相關代理商/技術參數
參數描述
XRT83L34 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L34_05 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L34ES 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83L34IV 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT83L34IV-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*