參數資料
型號： XC2S30-6VQ100C
廠商： Xilinx Inc
文件頁數： 49/99頁
文件大?。?/td> 0K
描述： IC FPGA 2.5V C-TEMP 100-PQFP
標準包裝： 90
系列： Spartan®-II
LAB/CLB數： 216
邏輯元件/單元數： 972
RAM 位總計： 24576
輸入/輸出數： 60
門數： 30000
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 100-TQFP
供應商設備封裝： 100-VQFP（14x14）
Spartan-II FPGA Family: DC and Switching Characteristics
DS001-3 (v2.8) June 13, 2008
Module 3 of 4
Product Specification
53
R
Power-On Requirements
Spartan-II FPGAs require that a minimum supply current
ICCPO be provided to the VCCINT lines for a successful
power-on. If more current is available, the FPGA can
consume more than ICCPO minimum, though this cannot
adversely affect reliability.
A maximum limit for ICCPO is not specified. Therefore the
use of foldback/crowbar supplies and fuses deserves
special attention. In these cases, limit the ICCPO current to a
level below the trip point for over-current protection in order
to avoid inadvertently shutting down the supply.
DC Input and Output Levels
Values for VIL and VIH are recommended input voltages.
Values for VOL and VOH are guaranteed output voltages
over the recommended operating conditions. Only selected
standards are tested. These are chosen to ensure that all
standards meet their specifications. The selected standards
are tested at minimum VCCO with the respective IOL and IOH
currents shown. Other standards are sample tested.
Symbol
Description
Conditions
New
Requirements(1)
For Devices with
Date Code 0321
or Later
Old
Requirements(1)
For Devices with
Date Code
before 0321
Units
Junction
Temperature(2)
Device
Temperature
Grade
Min
Max
Min
Max
I CCPO(3)
Total VCCINT supply
current required
during power-on
–40°C
≤ TJ<–20°C
Industrial
1.50
-
2.00
-
A
–20°C
≤ TJ < 0°C
Industrial
1.00
-
2.00
-
A
0°C
≤ TJ ≤ 85°C
Commercial
0.25
-
0.50
-
A
85°C < TJ ≤ 100°C
Industrial
0.50
-
0.50
-
A
TCCPO(4,5) VCCINT ramp time
–40°C
≤ TJ≤ 100°C
All
-
50
-
50
ms
Notes:
1.
The date code is printed on the top of the device’s package. See the "Device Part Marking" section in Module 1.
2.
The expected TJ range for the design determines the ICCPO minimum requirement. Use the applicable ranges in the junction
temperature column to find the associated current values in the appropriate new or old requirements column according to the date
code. Then choose the highest of these current values to serve as the minimum ICCPO requirement that must be met. For example,
if the junction temperature for a given design is -25°C
≤ TJ ≤ 75°C, then the new minimum ICCPO requirement is 1.5A.
If 5°C
≤ TJ ≤ 90°C, then the new minimum ICCPO requirement is 0.5A.
3.
The ICCPO requirement applies for a brief time (commonly only a few milliseconds) when VCCINT ramps from 0 to 2.5V.
4.
The ramp time is measured from GND to VCCINT max on a fully loaded board.
5.
During power-on, the VCCINT ramp must increase steadily in voltage with no dips.
6.
For more information on designing to meet the power-on specifications, refer to the application note XAPP450 "Power-On Current
Input/Output
Standard
VIL
VIH
VOL
VOH
IOL
IOH
V, Min
V, Max
V, Min
V, Max
V, Min
mA
LVTTL(1)
–0.5
0.8
2.0
5.5
0.4
2.4
24
–24
LVCMOS2
–0.5
0.7
1.7
5.5
0.4
1.9
12
–12
PCI, 3.3V
–0.5
44% VCCINT
60% VCCINT
VCCO + 0.5
10% VCCO
90% VCCO
Note (2)
PCI, 5.0V
–0.5
0.8
2.0
5.5
0.55
2.4
Note (2)
GTL
–0.5
VREF – 0.05
VREF + 0.05
3.6
0.4
N/A
40
N/A
GTL+
–0.5
VREF – 0.1
VREF + 0.1
3.6
0.6
N/A
36
N/A
HSTL I
–0.5
VREF – 0.1
VREF + 0.1
3.6
0.4
VCCO – 0.4
8
–8
HSTL III
–0.5
VREF – 0.1
VREF + 0.1
3.6
0.4
VCCO – 0.4
24
–8
HSTL IV
–0.5
VREF – 0.1
VREF + 0.1
3.6
0.4
VCCO – 0.4
48
–8
SSTL3 I
–0.5
VREF – 0.2
VREF + 0.2
3.6
VREF – 0.6
VREF + 0.6
8
–8
SSTL3 II
–0.5
VREF – 0.2
VREF + 0.2
3.6
VREF – 0.8
VREF + 0.8
16
–16
SSTL2 I
–0.5
VREF – 0.2
VREF + 0.2
3.6
VREF – 0.6
VREF + 0.6
7.6
–7.6
SSTL2 II
–0.5
VREF – 0.2
VREF + 0.2
3.6
VREF – 0.8
VREF + 0.8
15.2
–15.2
相關PDF資料
PDF描述
EP4S100G5F45I3N IC STRATIX IV FPGA 530K 1932FBGA
24LCS52-I/MS IC EEPROM 2KBIT 400KHZ 8MSOP
ABC60DREH-S13 CONN EDGECARD 120PS .100 EYELET
ACC60DREH-S13 CONN EDGECARD 120POS .100 EYELET
XC2S30-5VQ100I IC FPGA 2.5V I-TEMP 100-VQFP
相關代理商/技術參數
參數描述
XC2S30-6VQ100I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information
XC2S30-6VQG100C 制造商:Xilinx 功能描述:FPGA SPARTAN-II 30K GATES 972 CELLS 263MHZ 2.5V 100VTQFP - Trays
XC2S30-6VQG100I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S400E 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMS
XC2S400E-6FG456C 制造商:Xilinx 功能描述:FPGA SPARTAN-IIE 400K GATES 10800 CELLS 357MHZ 1.8V 456FBGA - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*