參數資料
型號: W25Q16DWSFIG
廠商: WINBOND ELECTRONICS CORP
元件分類: PROM
英文描述: 16M X 1 SPI BUS SERIAL EEPROM, PDSO16
封裝: 0.300 INCH, GREEN, PLASTIC, SOIC-16
文件頁數: 31/83頁
文件大?。?/td> 1268K
代理商: W25Q16DWSFIG
W25Q16DW
Publication Release Date: April 01, 2011
- 37 -
Preliminary - Revision A
M7-0
/CS
CLK
10.2.17 Word Read Quad I/O (E7h)
The Word Read Quad I/O (E7h) instruction is similar to the Fast Read Quad I/O (EBh) instruction except
that the lowest Address bit (A0) must equal 0 and only two Dummy clock are required prior to the data
output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code
execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status Register-2 must be set to
enable the Word Read Quad I/O Instruction.
Word Read Quad I/O with “Continuous Read Mode”
The Word Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 16a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Quad I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Quad I/O instruction (after /CS
is raised and then lowered) does not require the E7h instruction code, as shown in Figure 16b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered
after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the next
instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus returning to
normal operation. It is recommended to input FFh on IO0 for the next instruction (8 clocks), to ensure M4
= 1 and return the device to normal operation.
Figure 16a. Word Read Quad I/O Instruction (Initial instruction or previous M5-4
10, SPI Mode only)
Mode 0
Mode 3
0
1
IO
0
IO
1
IO
2
IO
3
2
3
4
5
20
16
12
8
21
17
22
18
23
19
13
9
14
10
15
11
A23-16
6
7
8
9
4
0
5
1
6
2
7
3
A15-8
A7-0
Byte 1
Byte 2
4
0
5
1
6
2
7
3
4
0
5
1
6
2
7
3
4
0
5
1
6
2
7
3
10
11
12
13
14
4
5
6
7
15
IOs switch from
Input to Output
Byte 3
16
17
18
19
20
21
Instruction (E7h)
Dummy
相關PDF資料
PDF描述
WMF128K8-90FFC5 128K X 8 FLASH 5V PROM, 90 ns, CDSO32
WMF128K8-70CLC5 128K X 8 FLASH 5V PROM, 70 ns, CQCC32
WS128K64V-20G4WM 1M X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQMA116
WS512K32-20G2M 2M X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQFP68
WS512K32F-25G4TM 2M X 8 MULTI DEVICE SRAM MODULE, 25 ns, QMA68
相關代理商/技術參數
參數描述
W25Q16DWSFIP 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIG 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIP 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSSIG 功能描述:IC FLASH SPI 16MBIT 8SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?(單線) 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-MSOP 包裝:帶卷 (TR)
W25Q16DWSSIP 制造商:WINBOND 制造商全稱:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI