- 您現在的位置：買賣IC網 > PDF目錄383961 > TMX320C6414TGLZ (Texas Instruments, Inc.) FIXED-POINT DIGITAL SIGNAL PROCESSORS PDF資料下載
參數資料
| 型號： | TMX320C6414TGLZ |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| 中文描述： | 定點數字信號處理器 |
| 文件頁數： | 53/140頁 |
| 文件大?。?/td> | 2033K |
| 代理商： | TMX320C6414TGLZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁
SPRS226H NOVEMBER 2003 REVISED AUGUST 2005
53
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
Terminal Functions (Continued)
SIGNAL
TYPE
IPD/
IPU
DESCRIPTION
NAME
NO.
UNIVERSAL TEST AND OPERATIONS PHY INTERFACE FOR ASYNCHRONOUS TRANSFER MODE (ATM) [UTOPIA SLAVE]
[C6415T and C6416T devices only]
UTOPIA SLAVE (ATM CONTROLLER) TRANSMIT INTERFACE
UXCLK
AD11
I
Source clock for UTOPIA transmit driven by Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXCLAV
AC14
O/Z
Transmit cell available status output signal from UTOPIA Slave.
0
indicates a complete cell is NOT available for transmit
1
indicates a complete cell is available for transmit
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXENB
AE15
I
UTOPIA transmit interface enable input signal. Asserted by the Master ATM Controller to indi-
cate that the UTOPIA Slave should put out on the Transmit Data Bus the first byte of valid data
and the UXSOC signal in the next clock cycle.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXSOC
AC13
O/Z
Transmit Start-of-Cell signal. This signal is output by the UTOPIA Slave on the rising edge of
the UXCLK, indicating that the first valid byte of the cell is available on the 8-bit Transmit Data
Bus (UXDATA[7:0]).
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
DX1/
UXADDR4§
AB11
I/O/Z
McBSP1 [default] or UTOPIA transmit address pins
As UTOPIA transmit address pins UXADDR[4:0] (
I
), UTOPIA_EN (BEA11 pin) = 1:
5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
NEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
FSX1/
UXADDR3§
AB13
I/O/Z
McBSP1 [default] or UTOPIA transmit address pins
As UTOPIA transmit address pins UXADDR[4:0] (
I
), UTOPIA_EN (BEA11 pin) = 1:
5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
FSR1/
UXADDR2§
AC9
I/O/Z
DR1/
UXADDR1§
AF11
I
UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
UXADDR0
AE9
I
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHAN-
NEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-k
IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-k
resistor should be used.)
§For the C6415T and C6416T devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414T device does
not
support the PCI or UTOPIA peripherals; therefore, these muxed peripheral pins are standalone peripheral functions
for this device.
For the C6415T and C6416T devices, external pulldowns required:
If
UTOPIA is selected (BEA11 = 1)
and
these pins are connected to other
devices, then a 10-k
resistor must be used to
externally
pull down each of these pins. If these pins are “no connects”, then only UXCLK and
URCLK need to be pulled down and other pulldowns are not necessary.
For the C6415T and C6416T devices, external pullups required:
If
UTOPIA is selected (BEA11 = 1)
and
these pins are connected to other devices,
then a 10-k
resistor must be used to
externally
pull up each of these pins. If these pins are “no connects”, then the pullups are not necessary.
Ψ
The C6414T device does not support the UTOPIA peripheral; therefore, these standalone UTOPIA pins are
Reserved
(leave unconnected,
do
not
connect to power or ground) with the exception of UXCLK and URCLK which should be connected to a 10-k
pulldown resistor (see the
square [ ] footnote).
相關PDF資料 |
PDF描述 |
|---|---|
| TMX320C6415TGLZ | FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMXF28155 | 155/51 Mbits/s SONET/SDH(155/51 M位/秒 SONET/SDH) |
| TN28F001BX-T150 | 1-MBIT (128K x 8) BOOT BLOCK FLASH MEMORY |
| TN28F001BX-T90 | 1-MBIT (128K x 8) BOOT BLOCK FLASH MEMORY |
| TN28F001BX-B150 | 1-MBIT (128K x 8) BOOT BLOCK FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMX320C6414TGLZ1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6415CGLZ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TMX320C6415CGLZ300 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6415CGLZ5E0 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
| TMX320C6415CGLZA300 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS |
發布緊急采購，3分鐘左右您將得到回復。