- 您現在的位置：買賣IC網 > PDF目錄297500 > TL16PNP100APT (TEXAS INSTRUMENTS INC) SPECIALTY MICROPROCESSOR CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TL16PNP100APT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP48 |
| 封裝： | PLASTIC, QFP-48 |
| 文件頁數： | 5/21頁 |
| 文件大?。?/td> | 304K |
| 代理商： | TL16PNP100APT |
TL16PNP100A
STANDALONE PLUG-AND-PLAY (PnP) CONTROLLER
SLLS200C – MARCH 1995 – REVISED SEPTEMBER 1997
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
PnP card configuration sequence
The PnP logic is quiescent on power up and must be enabled by software.
1.
The initiation key places the PnP logic into configuration mode through a series of predefined writes to
the ADDRESS port (see PnP Autoconfiguration Ports section).
2.
A serial identifier is accessed in bit-sequence and used to isolate the ISA cards. Seventy-two
READ_DATA port reads are required to isolate each card.
3.
Once isolated, a card is assigned a CSN that is later used to select the card. This assignment is
accomplished by programming the CSN.
4.
The PnP software then reads the resource-data structure on each card. When all resource capabilities
and demands are known, a process of resource arbitration is invoked to determine resource allocation
for each card.
5.
All PnP cards are then activated and removed from the configuration mode. This activation is
accomplished by programming the ACTIVE register.
PnP autoconfiguration ports
Three 8-bit ports (see Table 2) are used by the software to access the configuration space on each ISA PnP
card. These registers are used by the PnP software to issue commands, check status, access the resource data
information, and configure the PnP hardware.
The ports have been chosen so as to avoid conflicts in the installed base of ISA functions, while at the same
time minimizing the number of ports needed in the ISA I/O space.
Table 2. Autoconfiguration Ports
PORT NAME
LOCATION
TYPE
ADDRESS
0
×0279 (printer status port)
Write only
WRITE_DATA
0
×0A79 (printer status port + 0×0800)
Write only
READ_DATA
Relocatable in range 0
Read only
The PnP registers are accessed by first writing the address of the desired register to the ADDRESS port,
followed by a read of data from the READ_DATA port or a write of data to the WRITE_DATA port. Once
addressed, the desired register may be accessed through the WRITE_DATA or READ_DATA ports.
The ADDRESS port is also the destination of the initiation key writes (see PnP ISA specification).
The address of the READ_DATA port is set by programming the SET RD_DATA PORT register. When a card
cannot be isolated for a given READ_DATA port address, the READ_DATA port address is in conflict. The
READ_DATA port address must then be relocated and the isolation process begun again. The entire range
between 0
×0203 and 0×3FF is available; however, in practice it is expected that only a few address locations
are necessary before the software determines that PnP cards are not present.
相關PDF資料 |
PDF描述 |
|---|---|
| TL431BU | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, PDSO3 |
| TLE4252D | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PSSO4 |
| TLK4201EARGTRG4 | 4.25-GBPS CABLE AND PC BOARD EQUALIZER |
| TLK4201EARGTR | 4.25-GBPS CABLE AND PC BOARD EQUALIZER |
| TLK4201EARGTTG4 | 4.25-GBPS CABLE AND PC BOARD EQUALIZER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TL16PNP200 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:STANDALONE PLUG-AND-PLAY (PnP) CONTROLLER |
| TL16PNP200A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:STANDALONE PLUG-AND-PLAY (PnP) CONTROLLER |
| TL16PNP550A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:ASYNCHRONOUS COMMUNICATIONS ELEMENT WITH PLUG-AND-PLAY (PnP) AND AUTOFLOW CONTROL |
| TL16PNP550AFN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TL-17 | 功能描述:手工工具 TOOL RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
發布緊急采購，3分鐘左右您將得到回復。