- 您現在的位置：買賣IC網 > PDF目錄383938 > TDA1315H (NXP SEMICONDUCTORS) Digital audio input/output circuit DAIO PDF資料下載
參數資料
| 型號： | TDA1315H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | Digital audio input/output circuit DAIO |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| 文件頁數： | 10/36頁 |
| 文件大?。?/td> | 411K |
| 代理商： | TDA1315H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
1995 Jul 17
10
Philips Semiconductors
Product specification
Digital audio input/output circuit (DAIO)
TDA1315H
Whenever MUTE is activated in any of the transmit modes, the audio data of the IEC output signal will be muted and the
validity bit set to logic 0, regardless of the INVALID input value. When SDAUX is selected, MUTE will also affect the
output at pin SD.
Table 2
Summary of validity and muting in the transmit mode
Note
1.
X = don’t care.
INPUT CONDITIONS
(1)
IEC OUTPUT SIGNAL
MUTE ACTIVATED
SDAUX SELECTED
INVALID INPUT
VALIDITY BIT
AUDIO BITS
No
No
No
Yes
no
no
yes
X
0
1
X
X
0
1
0
0
from SD
from SD
from SDAUX
0
N
ON
-
AUDIO SECTION
In the non-audio section, the first 30 channel status bits
are taken from each block of data. A selection of 16 bits is
then assembled as two bytes and transferred to the user
interface. In the event of an incorrect IEC signal, i.e. no
consumer mode, an error will be flagged at pin CHMODE.
The error signal will return to its passive state after a full
block of consumer mode data has been received. The user
data bits are searched for the beginning of a ‘message’
(see Section “User data”), which is then stored bytewise in
a buffer that can be read by an external microcontroller via
the user interface. In the transmit mode, channel status
and user data bits are taken from an internal buffer that
has been written to by an external microcontroller via the
user interface. These bits are required for frame
composition in the biphase modulator.
The non-audio section supports only the consumer mode
of the “IEC 958”specification and handles the channel
status and user data information.
The non-audio section can be operated in the stand-alone
mode (receive only) and the host mode (transmit/receive).
In the stand-alone mode, a few bits from the channel
status are brought out to pins, the user data is not
available. In the host mode, channel status and user data
are exchanged using a microcontroller. After a RESET in
the host mode, the TDA1315H provides general format by
default.
Channel status
The channel status consists of 30 bits, a number of which
are reserved for future standardization. The 16 most
significant bits (MSBs), arranged as two bytes, are
exchanged using an external microcontroller. The
mapping of the channel status bits into these two bytes is
given in Tables 3 and 4. All SCMS operations (Serial Copy
Management System) will be performed in the
microcontroller and no manipulation in the TDA1315H is
possible. Bit 0 is always the first bit on the user interface.
In the receive mode, an error signal is generated at pin
CHMODE if a professional mode signal is received. Even
then, two bytes of information, mapped as defined in
Tables 3 and 4, are generated for output. Although there
are two bytes of channel status available for output, only
the first byte can be read. To identify future modes of the
channel status, both mode bits (bits 6 and 7 in the channel
status) are available (inverted) from the TDA1315H status
register. The channel status is created from the left
channel subframes of the IEC signal (preambles ‘B’
and ‘M’).
Whenever the channel status, as defined in
Tables 3 and 4 (16 bits), differs from the previously
received channel status, a bit will be set in the TDA1315H
status register. This helps to reduce the data traffic by
enabling the microcontroller to read the channel status
only after it has changed.
In the transmit mode, the microcontroller supplies
consumer mode (Mode 0) channel status data as
described in Table 3. Both bytes need to be transferred.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA1373H | General Digital Input GDIN |
| TDA1386 | Noise shaping filter DAC |
| TDA1386T | Noise shaping filter DAC |
| TDA1515AD | Single Audio Amplifier |
| TDA1515BQU | Single Audio Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA1315HB-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Audio |
| TDA1319 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| TDA1319T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Audio Tape Circuit |
| TDA1348AE | 功能描述:48V FAN 127X127X38MM RoHS:是 類別:風扇，熱管理 >> 風扇 - DC 系列:TDA 標準包裝:40 系列:OD8025 風扇類型:管軸式 尺寸/尺寸:方形 - 80mm L x 80mm H x 25mm W 電壓 - 額定:12VDC 功率（瓦特）:- 特點:PWM 控制；速度傳感器（轉速計） RPM:- 雜訊:- 靜態壓力:- 氣流:- 端子:4 引線 軸承類型:密封套筒 工作溫度:- 重量:- 額定電流:- 電壓范圍:- 預期壽命:- 其它名稱:OD802512MSS10A |
| TDA1348AE-EP | 功能描述:FAN 48VDC 127X38MM PWM/TACH/IP56 RoHS:是 類別:風扇，熱管理 >> 風扇 - DC 系列:TDA 產品培訓模塊:Cooling Solutions Computer Cooling in System Design Thermal Simulation in Telecom Applications RoHS指令信息:FAL6F24LH Material 產品目錄繪圖:FAL-6F_1 FAL-6F_2 FAL-6F_3 標準包裝:30 系列:FAL-6F 風扇類型:鼓風機 尺寸/尺寸:矩形/圓形- 109mm L x 111.4mm H x 28.1mm W 電壓 - 額定:24VDC 功率（瓦特）:7.08W 特點:- RPM:2550 RPM 雜訊:45 dB 靜態壓力:0.776 英寸水柱（193.2 Pa） 氣流:23.7 CFM（0.671m³/min） 端子:2 引線 軸承類型:流波 (HWB) 工作溫度:14 ~ 140°F（-10 ~ 60°C） 重量:0.551 磅（249.93g） 額定電流:0.295A 電壓范圍:14 ~ 27.6VDC 預期壽命:25°C 時為 30000 小時 產品目錄頁面:2688 (CN2011-ZH PDF) 其它名稱:FAL-6F24LHP9763 |
發布緊急采購，3分鐘左右您將得到回復。